Great Plains ADC2250 Operator Manual - Manual (Page 28)

26
Section 3 Adjustments
Model 2250 Air Drill Cart 167-033M 7/28/10
Great Plains Mfg., Inc.
Hybrid Pearl Millet Seed Rate Chart
85,500 - Seeds/Lb
Seed
Rate
Quick Change
Sprocket
(See Figure 3-6)
Driving/Driven Gears
(See Figure 3-1)
Gearbox
Shift
Levers
(See
Figure 3-3)
Seed
Rate
Quick Change
Sprocket
(See Figure 3-6)
Driving/Driven Gears
(See Figure 3-1)
Gearbox
Shift
Levers
(See
Figure 3-3)
Lbs/Acre Driving 1 Driven 2 Driving 3 Driven 4 Lbs/Acre Driving 1 Driven 2 Driving 3 Driven 4
1.9 20 30 17 54 E5 22.9 20 30 54 17 E5
2.2 20 30 17 54 D5 26.2 20 30 54 17 D5
2.5 20 30 17 54 E4 28.6 20 30 54 17 E4
2.7 20 30 17 54 C5 30.4 20 30 54 17 C5
2.9 20 30 17 54 D4 32.6 20 30 54 17 D4
3.1 20 30 17 54 E3 34.2 20 30 54 17 E3
3.3 20 30 17 54 B5 36.4 20 30 54 17 B5
3.5 20 30 17 54 C4 37.8 20 30 54 17 C4
3.6 20 30 17 54 D3 38.9 20 30 54 17 D3
3.7 20 30 17 54 E2 39.7 20 30 54 17 E2
4.3 20 30 17 54 E1 45.1 20 30 54 17 E1
4.3 20 30 17 54 D2 45.1 20 30 54 17 D2
4.3 20 30 17 54 C3 45.1 20 30 54 17 C3
4.3 20 30 17 54 B4 45.1 20 30 54 17 B4
4.3 20 30 17 54 A5 45.1 20 30 54 17 A5
4.9 20 30 17 54 D1 51.2 20 30 54 17 D1
5.1 20 30 17 54 C2 52.3 20 30 54 17 C2
5.2 20 30 17 54 B3 53.7 20 30 54 17 B3
5.5 20 30 17 54 A4 55.8 20 30 54 17 A4
5.8 20 30 17 54 C1 59.3 20 30 54 17 C1
6.2 20 30 17 54 B2 62.1 20 30 54 17 B2
6.6 20 30 17 54 A3 66.3 20 30 54 17 A3
7.1 20 30 17 54 B1 70.5 20 30 54 17 B1
7.8 20 30 17 54 A2 76.7 20 30 54 17 A2
9.0 20 30 17 54 A1 86.9 20 30 54 17 A1
4.9 30 20 17 54 E5 50.5 30 20 54 17 E5
5.6 30 20 17 54 D5 57.3 30 20 54 17 D5
6.2 30 20 17 54 E4 62.4 30 20 54 17 E4
6.6 30 20 17 54 C5 66.3 30 20 54 17 C5
7.1 30 20 17 54 D4 70.8 30 20 54 17 D4
7.5 30 20 17 54 E3 74.1 30 20 54 17 E3
8.0 30 20 17 54 B5 78.7 30 20 54 17 B5
8.4 30 20 17 54 C4 81.8 30 20 54 17 C4
8.6 30 20 17 54 D3 84.0 30 20 54 17 D3
8.8 30 20 17 54 E2 85.6 30 20 54 17 E2
10.1 30 20 17 54 E1 97.1 30 20 54 17 E1
10.1 30 20 17 54 D2 97.1 30 20 54 17 D2
10.1 30 20 17 54 C3 97.1 30 20 54 17 C3
10.1 30 20 17 54 B4 97.1 30 20 54 17 B4
10.1 30 20 17 54 A5 97.1 30 20 54 17 A5
11.6 30 20 17 54 D1 110.0 30 20 54 17 D1
11.9 30 20 17 54 C2 112.2 30 20 54 17 C2
12.2 30 20 17 54 B3 115.2 30 20 54 17 B3
12.7 30 20 17 54 A4 119.8 30 20 54 17 A4
13.6 30 20 17 54 C1 127.4 30 20 54 17 C1
14.3 30 20 17 54 B2 133.5 30 20 54 17 B2
15.3 30 20 17 54 A3 142.7 30 20 54 17 A3
16.4 30 20 17 54 B1 152.0 30 20 54 17 B1
17.9 30 20 17 54 A2 166.2 30 20 54 17 A2
20.5 30 20 17 54 A1 190.7 30 20 54 17 A1
1 Connected to the gearbox output shaft. 2 Connected to the meter input shaft. 3 Located on the front/upper shaft of the meterbox. 4 Located on the lower/back shaft of the meterbox