Quoizel ALZ5005PN Aliza - Manual

Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax
631.231.7102
www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire
strippers, electrical tape, safety glasses.
Estimated Assembly Time: 35-40 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package
content list and diagrams below to be sure all parts are present. If any parts are missing
or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer
service for replacement parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Assembly Instruction Sheet #IS-ALZ5005PN
For Style ALZ5005PN
Bulb Recommended: alternate bulbs (5) Medium Base 23W CFL (5) Medium Base 100W Maximum,
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
1of3
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2013 QuoizelInc. December2013
STEP 1 - Attach Fixture Loop to
Fixture Assembly
A. Unfold Support Arms of the Fixture
Assembly (B) to proper locations.
B. Thread the Fixture Loop (A) onto
the nipple on the top end of the
Fixture Assembly (B). Hand
tighten until snug.
(Refer to Shade Orientation)
Figure 1
SHADE ORIENTATION
Package Contents
A
B
C
D
E
Fixture Loop
x 1
Socket Assembly
x 1
Socket Collar Tool
x 1
Shade
x 5
Socket Collar
x 5
STEP 2 Install Crossbar -
A. AA) Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included)
Tighten until snug . .
Figure 2
Outlet Box
Outlet Box Screw
(not included)
Green Ground Screw
AA
STEP 3 Install Canopy Chain Loop and Nipple -
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end
of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).
Place another Lock Washer (BB) over the Nipple (DD) and then
thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD)
Figure 3
AA
BB
CC
DD
CC
BB
EE
FF
HH
Step A
Step B
Hardware Contents
AA
BB
CC
DD
EE
FF
HH
Crossbar
x 1
Lock Washer
x 2
Hex Nut
x 2
Nipple
x 1
Canopy Chain Loop
x 1
Canopy Lock Ring
x 1
Ceiling Canopy
x 1
GG
Fixture Chain
x 1
A
B