SoundOff Signal 400 Series Handheld Siren - Manual (Page 3)

1.800.338.7337 / www.soundoffsignal.com
Operating Modes
The primary operating modes are User
Selectable Tone, Yelp, Wail, Radio and PA.
Horn Override and a push-button Manual
Override are available in all modes. For
California Title 13 compliance all tones
except Wail and Yelp may be disabled by
programming the siren.
-Holster Installation-
A holster is provided for mounting the hand held remote. Choose a
location convenient to the operator and away from any air bag deploy-
ment areas. Using the back plate as a template, mark the 4 holes to
be drilled. Using a 1/8” drill bit, drill the mounting holes. Install the 4
#6 screws provided with the bracket.
WIRING:
WARNING! All customer supplied wires connecting to the
positive terminal of the battery must be sized to supply at least
125% of the maximum operating current and FUSED at the
battery to carry that load.
Ensure the siren amplifier / relay unit is mounted in dry, protected
environment.
TECHNICAL SPECIFICATIONS
Overall Dimensions:
Control Panel:
Amplifier/Relay:
3.51”H x 6.98”W x 1.17”D
2.62”H x 7.00”W x 6.51”D
Input Voltage: 10 - 16Vdc (negative ground)
Boxed Weight: 8 lbs.
Operating Temperature: -40°C to +50°C
Diagnostic LEDs: Speaker shorted/open, internal fuses open,
communications faults, over/under voltage
Siren
Input Current: 7 Amps @ 13.4 VDC (100W) Speaker
14 Amps @ 13.4VDC (2x100W speakers)
Standby Current:
Ignition ON:
Ignition OFF:
500mA
<1mA
Audio Frequency: 500-3 kHz
Output Power: ETSA461: 1x100W RMS Max (11 Ohm speaker)
ETSA462: 2x100W RMS Max (11 Ohm speaker)
Siren Frequency: 675Hz - 1633Hz
High Voltage
Protection:
Limits to < 18V:*
*If siren tone is in progress, sound will continue
during overvoltage. New siren tone will not
activate if voltage is >18V.
Low Voltage Shutdown: Voltage <9.0V will cause siren output to cease and
will resume when system voltage is >9.5V
Tone disable for California Title 13 compliance
Auxiliary Input connection for remote manual or
Hands Free operation
Speaker Protection: Shorted, Open: Stop output signal, preserve Amp
Light Control
AUX Button Relays: 9 total 10A max each circuit, total current not to
exceed 50A for CN8 pin 5
2 of the 9 available for external arrow control
2 of the 9 have their source voltage switchable
form internal to external via fuse location, see pg5
Slide Switch Relays: 3 total 20A max each circuit, total current not to
exceed 50A for CN8 pin 4
WARNING !
Do not install this product or route its wires in
the air bag deployment area.
Doing so may cause damage to or reduce
effectiveness of the air bag, or create projectile
that could cause serious injury or death.
To determine air bag deployment area refer to
vehicle manufacturer's manual.
MOUNTING
-Amplifier Installation-
Before drilling holes, check for clearance to prevent
damage. Check both sides of the mounting surface
before drilling and the be aware of any vehicle
components or other vital parts that may be damaged
during drilling.
Install grommets in any wire passage holes.
1. Slide ¼” hex head bolts into siren amplifier t-slots.
2. Place mounting brackets over bolts.
3. Thread ¼” lock nuts onto bolts and tighten down.
4. Use mounting bracket holes to secure amplifier.
5. Install amplifier with clearance from other objects
for improved ventilation.
1
2
4
400 SERIES AMPLIFIER BOX
PSRN4ANR1
PSRN4ANR2
3
ETSA46(x)HPP-cvr 11.13