Watts WPFP12-25W - Manual

For Residential and Commercial Applications
ES-WP-FastPacks
Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor ––––––––––––––––––––––––––––––––––––––––––––
Job Location ––––––––––––––––––––––––––––––––––––––––– Approval –––––––––––––––––––––––––––––––––––––––––––––
Engineer ––––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. ––––––––––––––––––––––––––––––––––
Approval ––––––––––––––––––––––––––––––––––––––––––––– Representative ––––––––––––––––––––––––––––––––––––––––
WaterPEX ® Fast Packs
WPFP
10ft. Fast Pack Bundle
LEAD FREE
*
Watts Fast Packs are uniquely designed with the repair plumber
and retrofit contractor in mind. Each fast pack is pre-cut to 10'
lengths and packaged in a convenient, easy to carry, heavy-duty
8 mil plastic sheathe. The Fast Pack is made to fit easily into the
bed of a pick-up truck or service van and does not require two
people to load or unload.
Features
• Available in 1 ⁄
2
" and 3 ⁄
4
", Red, Blue and White
• Pre-cut to 10' lengths and wrapped in a heavy-duty
plastic sheathe
• Easy to load and unload into pick-up truck or service van
• Requires only one person to handle
Temperature – Pressure
Maximum Working Pressure:
160psi (11 bar) @ 73.4ºF (11 bar @ 23ºC)
100psi (6.9 bar) @ 180ºF (6.9 bar @ 80ºC)
80psi (5.5 bar) @ 200ºF (5.5 bar @ 93ºC)
Specifications
System shall be plumbed using Watts cross-linked polyethylene
pipe, and all joints shall be made using Watts brass CrimpRing ™
and/or Poly-alloy CrimpRing ™ fittings using either the Watts
copper CrimpRing ™ or stainless steel CinchClamp ™ ** crimping
methods as outlined in the Watts Installation Guidelines.
Installation Note
WaterPEX ® must be installed in accordance with all Watts
WaterPEX ® installation procedures, including information pro-
vided in WaterPEX ® installation manual and guidelines.
WaterPEX ® Fast Packs are not approved for fire
protection applications.
Connections
WaterPEX ® is connected to WaterPEX ® manifolds or barbed
fittings using one of two connection systems, depending on
manifold type or fitting system specified. See chart below:
Approvals
• Manufactured in accordance with American Society for Test-
ing and Materials (ASTM International) F876 and F877 to
SDR-9 dimensional standards
• Listed by the NSF International to NSF Standards 14 and 61
for use in potable water systems
• Listed by NSF International to be in compliant to the Uniform
Plumbing Code
• Labeled B137.5 which indicates that it is compliant to the
CSA Standards B137.5
* The wetted surface of this product contacted by consumable
water contains less than one quarter of one percent (0.25%) of
lead by weight.
** Note: Watts WaterPEX CinchClamp ™ fittings should not be used
with wrought copper PEX fittings.
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,
please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials with-
out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
✓ Fitting Style deSScriPtion
CrimpRing Fittings
Ductile Copper CrimpRing ™ compressed over
WaterPEX/CrimpRing fitting.
Compression Fittings Brass Compression Nut tightened around WaterPEX
®
and CompNut ™ fitting.