Watts WPDT - Manual

Series WPDT
Brass CrimpRing™ DripTees
Sizes: 1 ⁄ 2 ", 3 ⁄ 4 ", 1" (15, 20, 25mm)
Brass CrimpRing ™ DripTees are used for draining water in
potable systems.
Specifications
System shall be plumbed using Watts WaterPEX ® cross-linked
polyethylene pipe, and all joints shall be made using Watts
brass CrimpRing
™ and/or polyalloy CrimpRing ™ fittings using
either the Watts copper CrimpRing ™ or stainless steel
CinchClamp ™ crimping methods as outlined in the Watts
WaterPEX ® Installation Guidelines.
Installation Note
CrimpRing ™ DripTees must be installed in accordance with all
Watts WaterPEX ® installation procedures, including information
provided in WaterPEX ® installation manual and guidelines.
• Manufactured in accordance with American Society for
Testing and Materials (ASTM) F-877 and F-1807
• Listed by the National Sanitation Foundation to NSF
Standards 14 and 61 for use in potable water systems
• Listed by NSF to be in compliant to the Uniform Plumbing
Code
• Labeled B137.5 which indicates that it is compliant to the
CSA Standards B137.5
Dimensions – Weights
Approvals
For Residential and Commercial Applications
ES-WP-DripTees
Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor ––––––––––––––––––––––––––––––––––––––––––––
Job Location ––––––––––––––––––––––––––––––––––––––––– Approval –––––––––––––––––––––––––––––––––––––––––––––
Engineer ––––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. –––––––––––––––––––––––––––––––––––
Approval ––––––––––––––––––––––––––––––––––––––––––––– Representative ––––––––––––––––––––––––––––––––––––––––
W a r n i n g !
If connections must be made in temperatures below 30°F,
caution must be taken to allow the WaterPEX to form a proper
seal against the barb. Apply the connection slowly to ensure
the PEX material conforms to the barb.
WPDT
CrimpRing ™ DripTee
MODEL 1 2 3 PKG. WEIGHT
in. mm type in. mm type in. mm type lbs. kgs.
WPDT-08 1 ⁄ 2 15 Crimp Fitting 1 ⁄ 2 15 Crimp Fitting 3 ⁄ 8 10 w/Cap 0.1 0.045
WPDT-12 3 ⁄ 4 20 Crimp Fitting 3 ⁄ 4 20 Crimp Fitting 3 ⁄ 8 10 w/Cap 0.15 0.068
WPDT-16 1 25 Crimp Fitting 1 25 Crimp Fitting 3 ⁄ 8 10 w/Cap 0.21 0.09
1
3
2
ES-WP-DripTees 0736 © Watts, 2007
USA: 815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com
Canada: 5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanada.ca
W a t e r P E X P l u m b i n g P r o d u c t s
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts
reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications
on Watts products previously or subsequently sold.
ES-WP-DripTees.qxd 3/10/09 9:20 AM Page 1