Watts WP27P-16PB - Manual

Poly-Alloy CrimpRing ™ Test Plugs are used for pressure testing
the system.
Specifications
System shall be plumbed using Watts WaterPEX ® cross-linked
polyethylene pipe, and all joints shall be made using Watts
brass CrimpRing ™ and/or poly-alloy CrimpRing ™ fittings using
either the Watts copper CrimpRing ™ or stainless steel
CinchClamp ™ ** crimping methods as outlined in the Watts
WaterPEX ® Installation Guidelines.
Installation Note
CrimpRing ™ Test Plugs must be installed in accordance with all
Watts WaterPEX ® installation procedures, including information
provided in WaterPEX ® installation manual and guidelines.
Approvals
• Manufactured in accordance with American Society for
Testing and Materials (ASTM) F-877 and F-2159
• Listed by the National Sanitation Foundation to NSF
Standards 14 and 61 for use in potable water systems
• Listed by NSF to be in compliant to the Uniform Plumbing
Code
• Labeled B137.5 which indicates that it is compliant to the
CSA Standards B137.5
• Manufactured from Acudel ® engineered thermoplastic resin
Dimensions – Weights
For Residential and Commercial Applications
ES-WP-PATestPlugs
Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor ––––––––––––––––––––––––––––––––––––––––––––
Job Location ––––––––––––––––––––––––––––––––––––––––– Approval –––––––––––––––––––––––––––––––––––––––––––––
Engineer ––––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. ––––––––––––––––––––––––––––––––––
Approval ––––––––––––––––––––––––––––––––––––––––––––– Representative ––––––––––––––––––––––––––––––––––––––––
Warning!
If connections must be made in temperatures below 30°F,
caution must be taken to allow the WaterPEX to form a proper
seal against the barb. Apply the connection slowly to ensure
the PEX material conforms to the barb.
WP27P
CrimpRing ™ Test Plug
Model ConneCTion Pkg. WeighT
in. mm type lbs. kgs.
WP27P-06PB 3 ⁄
8
10 Crimp Fitting 1 0.4
WP27P-08PB 1 ⁄
2
15 Crimp Fitting 1 0.4
WP27P-12PB 3 ⁄
4
20 Crimp Fitting 2 0.9
WP27P-16PB 1 25 Crimp Fitting 2 0.9
Poly-Alloy CrimpRing ™
Test Plugs
ES-WP-PATestPlugs 1020 © 2010 Watts
USA: 815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com
Canada: 5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanada.ca A Watts Water Technologies Company
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts
reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications
on Watts products previously or subsequently sold.
LEAD FREE
*
* The wetted surface of this product contacted by consumable
water contains less than one quarter of one percent (0.25%) of
lead by weight.
** Note: Watts WaterPEX CinchClamp ™ fittings should not be used
with wrot copper PEX fittings.