116fm (globe) - pressure relief valve, Dimensions - acv 116fm (globe), Installation and start-up – Watts 116FM User Manual
Page 2: 125 by: checked by: revision: supercedes
DIMENSIONS - ACV 116FM (Globe)
0
60
30
300
240
270
90
180
150
120
210
AC
V
WA
TT
S
XX
X
TITLE:
DRAWING NUMBER:
NAME:
DATE:
DESIGN BY:
DRAWN BY:
CHECKED BY:
APPROVED BY:
REVISIONS:
DATE:
TOLERANCES:
EXCEPT
AS
NOTED
FRACTIONAL
ANGULAR
DECIMAL
.XX DIMS
.XXX DIMS
.XXXX DIMS
SCALE
SURFACE
EXCEPT
AS
NOTED
+
+
+
+
+
1/64
1/2°
.01
.005
.001
125
BY:
CHECKED BY:
REVISION:
SUPERCEDES:
CONTROL
VALVE
AUTOMATIC
HOUSTON, TEXAS
WATTS AUTOMATIC CONTROL VALVE COMPANY
VALVE SIZE
INCH - MM
3 80
6 150
A
150
300
B
C
D
7.875
13.22
21.00
12.00
20.00
13.25
10.125
15.00
9.75
11.50
INLET
OUTLET
6 INCH GLOBE
116 FM ASSEMBLY
4 100
8 200
A
B
C
D
9.97
16.00
25.38
15.63
26.38
15.00
10.50
18.50
10.00
13.00
Valve Size
150 Outlet
300 Outlet
A
A
B
C
D
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
3
80
12
305
13
1
⁄
4
337
10
1
⁄
8
257
7
7
⁄
8
200
9
3
⁄
4
248
4
100
15
381
15
5
⁄
8
397
10
1
⁄
2
267
9
15
⁄
16
252
10
254
6
150
20
508
21
533
15
381
13
1
⁄
4
337
11
1
⁄
2
292
8
800
25
3
⁄
8
645
26
3
⁄
8
670
18
1
⁄
2
470
16
406
13
330
USA: • Tel. (713) 943-0688 • (713) 944-9445 • www.watts.com
116FM (Globe) - Pressure Relief Valve
Installation and Start-up
Start-up of an Automatic Control Valve requires following proper procedures. Time must be allowed for the valve to react
to adjustments and the system to stabilize. The objective is to bring the valve into service in a controlled manner to protect
the system from damaging overpressure.
NOTICE: Avoid mounting valves in a vertical discharge postion (valve stem horizontal or cover pointed sideways.) Valves mounted in
this position may not perform as tested and approved.
•
Clear the line of slag and other debris.
•
Install the valve so that the FLOW ARROW marked on the valve body matches the flow through the line.
•
Install pressure gauge (supplied) in the fitting on valve tubing.
1. Turn the Relief Control adjustment screw counterclockwise (out). This lowers the initial relief set-point, allowing the set-point to be
increased to the desired setting.
2. Loosen a tube fitting at a high point on the valve. This allows the cover to vent trapped air during initial filling of the valve.
3. Start the pump to supply fluid/pressure to the valve.
4. Tighten the tubing when all air is vented from the cover as indicated by continual flow of fluid.
NOTICE: THE RELIEF SET-POINT SHOULD BE LOWER THAN DESIRED AT THIS TIME.
5. Turn the Relief Control adjustment screw clockwise (in) slowly, allowing time for the pressure to gradually increase to the desired
set-point.