Watts LFIS6301 - Manual

= This valve is designed to be soft soldered into lines without
disassembly using low temperature solder (420°F, 216°C). Other
solders, such as 95/5 tin antimony (460°F, 238°C) or 96/4 tin
silver (430°F, 221°C), can be used. However, extreme caution
must be used to prevent seat damage. Higher temperature
solders will damage the seat material. ANSI B16.18 states that
the maximum operating pressure of 50-50 solder connection
is 200psi (14 bars) at 100°F (38°C) and decreases with higher
temperatures.
Apply heat with the flame directed AWAY from the center of the
valve body. Excessive heat can harm the seats. After soldering,
the packing nut may have to be tightened.
2-Piece, Full Port, Ball and Waste
Brass Ball Valves
Sizes: 1 ⁄
2
" – 1" (15 – 25mm)
Series LFIT6300, LFIS6301 2-Piece, Full Port, Ball and Waste
Lead Free* Copper Silicon Alloy Ball Valves feature a side drain
port to drain or vent downstream line when the valve is in the
off position. The LFIT6300, LFIS6301’s full port orifice ensures
maximum flow capacity and its ball is wiped clean during each
operation of the valve. The LFIT6300, LFIS6301 features Lead
Free* construction to comply with Lead Free* installation require-
ments.
Features
• Drainportallowsdrainingorventingofdownstreamlinewhen
valve is in the off position
• Fullport
• VirginPTFEvalveseatsarestandard.Suitableforafullrange
of liquids and gases. Consult factory for specific applications
• Balliswipedcleanduringeachoperationofthevalve
• Blow-outproof,pressureretainingstem
• Vinylinsulatoronheavydutyhandles
• Fast,quarter-turnopenorcloseoperation
• Lowoperatingtorque
• Adjustablestempackinggland
Models
LFIT6300 1/2" – 1" (15 – 25mm) threaded NPT end connections
LFIS6301 1/2" – 1" (15 – 25mm) solder end connections
=
Specifications
A 2-piece, full port, ball and waste brass ball valve shall be
installed as indicated on the plans. Lead Free* 2-Piece, Full Port,
Ball and Waste Lead Free* Copper Silicon Alloy Ball Valves shall
be constructed using Lead Free* materials. Lead Free valves
shall comply with state codes and standards, where applicable,
requiring reduced lead content. The valve shall have a side drain
port to drain or vent downstream line when valve is in the off
position. Valve shall have blow-out proof stems, virgin PTFE
seats and full port. Valve shall be pressure rated at 600psi (41
bars) WOG non-shock. Valve shall be a Watts Series LFIT6300
(threaded) or LFIS6301 (solder).
LFIT6300
LFIS6301
For Commercial and Industrial Applications
ES-LFIT_LFIS6300
Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor ––––––––––––––––––––––––––––––––––––––––––––
Job Location ––––––––––––––––––––––––––––––––––––––––– Approval –––––––––––––––––––––––––––––––––––––––––––––
Engineer ––––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. ––––––––––––––––––––––––––––––––––
Approval ––––––––––––––––––––––––––––––––––––––––––––– Representative ––––––––––––––––––––––––––––––––––––––––
Series LFIT6300,
LFIS6301
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,
please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials with-
out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
LEAD FREE
*
*The wetted surface of this product contacted by consumable
water contains less than 0.25% of lead by weight.