Replacing spare parts, Replacing spare parts 20 – MTS AHX800 High Elongation Extensometer User Manual
Page 20
AHX800 High Elongation Extensometer Product Manual
20
Replacing Spare Parts
Maintenance
Replacing Spare Parts
The topics on the following pages describe how to replace the spare parts. See the
following figure for component identification.
Knife edges
1. Remove the screw securing a knife edge.
2. Replace the old knife edge with a new one.
3. Secure the knife edge with the screw.
4. Repeat this procedure for all the knife edges.
Leaf arm
1. Remove the knurled knob.
2. Remove the screws securing the rear of the leaf arm.
3. Transfer the components from the old arm to the new one.
4. Loosely attach the leaf arm to the block, and screw the knurled knob back on.
5. Adjust the arm so that it is parallel with the other arms and tighten the screws.
Teflon slide
1. Remove the two screws securing the Teflon slide and replace it.
Teflon Slide
Clamping
Force Spring
Leaf Arm
High Energy
Spring
Component Identification
Knife
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)