MBT Lighting CX1603 User Manual

Page 9

For example, make a setting on the 11th pattern so that ch.1 to ch.16 to be full on is sequence.

Ⅰ、

Press PROGRAM button for more than one seconds to enter PROGRAM mode, the matching indicator is

lit.

Ⅱ、

Press PATTERN+ or PATTERN- and STEP+ or STEP- till the LCD shows 11:01

Ⅲ、

Slide the fader 1 to up position and the other faders to down position, press LATCH 9-16 buttons to turn all

matching indicator off. After this setting press PROGRAM button once, now the LCD would show 11:02

Ⅳ、

Slide the fade 2 to up position and the other faders to down position, press LATCH 9-16 to turn all

matching indicator off After this setting, press PROGRAM button once again, now the LCD would show 11:03

Ⅴ、

Follow your setting as specified by Ⅲ. And Ⅳ till the LCD shows 11:09 Slide all the fader to down

Position and press LATCH 9-16 to turn channel 9 indicator on and the other indicators off Press PROGRAM

button once, the LCD shows 11:10

Ⅵ、

Continue your setting till the LCD shows 11:17, now press STEP-button to alert 11:17 to 11:16

Ⅶ、

Press SHIFT+END STEP to define the 16th

step to the last step. now the pattern is complete.

ASSIGN PROGRAM

There are 16 ASSIGN for the levels set by fader 1 to fader 8 and LATCH 9-16 buttons.

For example. to assign CH.1 to CH.9 full on and CH.10 to CH.16 blackout to FLASH 1 button, you should

follow the steps.

Ⅰ、

Press ASSIGN button for more than one seconds to enter ASSIGN PROGRAM mode, the matching

indicator is lit.

Ⅱ、

Slide fade 1 to fade 8 to up position, press LATCH 9 button to turn channel 9 indicator on.

Ⅲ、

Press ASSIGN button first. Then press FLASH 1 button, all channel indicators would flash three

times ,now ASSIGN 1 is complete.

PATCH SETTING

In PATCH mode, you could allocate easily the outgoing DMX channels to your light fixtures.

For example. to allocate 1-16 DMX channels to 16-1 channels, please proceed as follows.

Ⅰ、

Press PATCH button for more than one second to enter PATCH mode. the matching indicator is lit. Press

STEP+OR step –till the LCD shows 01 in the right two digits.

Ⅱ、

Press PATTERN+ or PATTER- till the LCD shows 16 in the left two digits. now the 1st DMX channel is

relocated to the level of the 16th channel.

Ⅲ、

Press STEP+, the LCD shows 02 in the right side, press PATTER-, the LCD shows 15 in the left side, now

the 2nd DMX channel is relocated to the level of the 15th channel.

Ⅳ、

Follow the settings as specified by Ⅲ. Till the 16th DMX channel is relocated to the level of the 1st

channel. Press PATCH button for more than one second to leave PATCH mode. the matching indicator is off.

RUN PATTERN IN CROSS MODE

In CROSS mode, the patterns are executed step by step by sliding the MASTER fader up and down

repeatedly.

Ⅰ、

In CHASE mode, press SHIFT+CROSS SETUP, the CROSS ON indicator is lit.

Ⅱ、

Slide the MASTER fader to top position, press CROSS button to enter CROSS mode, the A indicator is lit.

Ⅲ、

Press PATTERN+ or PATTERN- till the LCD shows 11:01.

Ⅳ、

Turn the LEVEL knob to maximum, now the A indicator is full.