Dip on – Comelit MT 8172IS User Manual
Page 31
31
31
EN
Take note of the S2, S1 setting and restore it when programming is complete
1)
2)
3)
4)
S1
DIP
1
DIP
2
DIP
3
DIP
4
DIP
5
DIP
6
S2
S1/S2/LED1
1
1
1
1
1
1
4AKEæ NOTEæ OFæ THEæ
S2, S1
SETTINGæANDæ
RESTOREæ ITæ WHENæ
PROGRAMMINGæ
ISæ
COMPLETE
Factory settings:
sæ"UTTONæFUNCTIONSæFORæTHEæ3æ$)0æSWITCHæ
æCOMBINATION
sæ)NTERCOMæADDRESSæABSENT
sæ2ANGEæFUNCTIONæANDæMINMAXæADDRESSESæABSENT
sæ2INGTONEæRESET
sæ)NPUTæ).жжж,%$жDEFAULT
DIP ON
2
1
KO Prog.
5 sec
OK Prog.
Programming reset
!LLOWSæDIRECTæPROGRAMMINGæOFæINTERCOMæCALLæVIAæTHEæINTERNALæUNITS
√ 2EQUIRESææOPERATORS
Step 1: enter programming mode
Operator 1 and Operator 2 carry out the following procedures
on 2 internal units:
æ3ETж3ж$)0æSWITCHESæ
æ
æTOæTHEæCOMBINATIONæ
æ0RESSæANDæHOLDæBUTTONSæææANDææFORææSEC
»The internal unit emits 1 tone.
»The red LED flashes.
»The blue audio LED lights up.
»The internal unit enters audio mode.
»At this point the 2 operators will be communicating with each
other.
____
Step 2 (optional): intercom audio volume adjustment
æ!DJUSTæTHEæINTERCOMæAUDIOæVOLUMEæUSINGæTHEæAUDIOæADJUSTMENTæKNOBææ
æ0RESSæKEYæææ
A TOæCONlRM
»The internal unit emits 1 tone.
»The blue lock-release LED flashes.
»The monitor memorises the audio setting for intercom calls.
æ!Tæ THEæ ENDæ OFæ THEæ AUDIOæ ADJUSTMENTæ SETæ THEæ EXTERNALæ UNITæ AUDIOæ
VOLUMEæADJUSTMENTæKNOBææ æBACKæTOæITSæPREVIOUSæPOSITION
Direct programming of intercom call
_____________________
Step 3: intercom call programming
Operator 1:
` 0RESSæTHEæBUTTONæYOUæWANTæTOæPROGRAMæTOæCALLæOPERATORææEGæ
»The internal unit manned by operator 1 emits a confirmation tone.
Operator 2:
` 0RESSæTHEæBUTTONæYOUæWANTæTOæPROGRAMæTOæCALLæOPERATORææEGæ
»The internal unit manned by operator 2 emits a confirmation tone.
Operator 1/Operator 2:
` 0RESSæTHEæBUTTONæ
»The blue audio LED switches off.
»Programming of the 2 internal units is now complete.
4OæPROGRAMæANOTHERæINTERNALæUNITæMOVEæONæTOæ34%0æ
____
Step 4: programming other internal units
Operator 1/Operator 2:
/NCEæ THEæ NEWæ STATIONæ HASæ BEENæ REACHEDæ CARRYæ OUTæ STEPæ æ TOæ
BEGINæCOMMUNICATION
æ2EPEATæSTEPææ
NOTE
)FæAæCALLæISæRECEIVEDæDURINGæPROGRAMMINGæITæMUSTæBEæANSWEREDæ
ANDæTHEæPROGRAMMINGæPROCEDUREæRESUMEDæAFTERWARDS