Service & maintenance, Service & maintenance 5, Warning – Echo CH9540H Owners Manual v.4 User Manual
Page 17: English, Service and maintenance schedule
PTO CHIPPERS
13
ENGLISH
Section
SERvICE aNd maINTENaNCE SCHEduLE
FREQuENCY
CompoNENT
maINTENaNCE
REQuIREd
REFER To
ENGINE
opERaToR’S
maNuaL
bEFoRE
EaCH
uSE
EvERY
8
HouRS
EvERY
25
HouRS
EvERY
50
HouRS
EvERY
200
HouRS
EvERY
YEaR
AIR cleANeR
check ANd cleAN (1)
AIR INTAke
cleAN (1)
hYdRAulIc OIl
check/FIll
All INTeRNAl ANd
exTeRNAl NuTS ANd
BOlTS
check TIGhTNeSS
chIPPeR ANVIl
check cleARANce ANd
Re-TORQue TO 75 FT-
lBS. (2)
chIPPeR BlAdeS
check ShARPNeSS ANd
Re-TORQue MOdelS
ch8540 ANd ch9540h
TO 120 FT-lBS. TORQue
MOdel chF9540h TO 25
FT-lBS. (2)
eNTIRe MAchINe
cleAN
PTO cROSS jOuRNAlS
luBe
PTO INNeR TuBeS
luBe
PTO ShIeld ReTAINING
BeARING
luBe
dRIVe BelT
check
hYdRAulIc dRIVe BelT
check
BelT TeNSION
check
BelT/PulleY AlIGNMeNT
check
GReASe ZeRkS
luBe
hYdRAulIc OIl FIlTeR
RePlAce
Wheel BeARINGS
check ANd RePAck
(1) PeRFORM MORe FReQueNTlY uNdeR exTReMelY duSTY cONdITIONS.
(2) PeRFORM MORe FReQueNTlY WheN chIPPING dRY OR dIRTY WOOd.
as the Limited Warranty states, failure by the owner to perform normal maintenance will void the machine’s warranty.
The aggressive, high-speed nature of chipping REQuIRES THE oWNER To pERFoRm THE abovE LISTEd NoRmaL
maINTENaNCE. Special consideration to maintain and re-torque the CHIppER aNvIL, CHIppER bLadES, aNd aLL
INTERNaL aNd ExTERNaL NuTS aNd boLTS is the sole responsibility of the owner. Failure by the owner to do so
shall be cause for denial of warranty.
SERvICE & maINTENaNCE
5
The items listed in this service and maintenance schedule
are to be checked, and if necessary, corrective action taken.
This schedule is designed for units operating under normal
conditions. If the unit is operating in adverse or severe
conditions, it may be necessary for the items to be checked
and serviced more frequently.
SEE ENGINE oWNER’S maNuaL FoR FuRTHER
ENGINE maINTENaNCE aNd TRoubLESHooTING
INFoRmaTIoN.
WaRNING
To prevent personal injury or property damage: shut
off engine and make sure that all moving parts have
come to a complete stop before servicing, adjusting,
or repairing machine. disconnect the battery and
remove ignition key where applicable.