beautypg.com

4 raise extension tray before towing, 5 feed roller control bar, Warning – Echo CH9540H Owners Manual v.4 User Manual

Page 15: English

background image

PTO CHIPPERS

11

ENGLISH

OPERATION

4.5 FEEd RoLLER CoNTRoL baR

WaRNING

To prevent personal injury or property damage: shut

off engine and make sure that all moving parts have

come to a complete stop before servicing, adjusting,

or repairing machine. disconnect the battery and

remove ignition key where applicable.

The Feed Roller Control bar is used to manually control

the direction of the feed roller rotation.
Move the feed roller control bar to FORWARd (F) when

you want the materials to feed into the chipper. The

controller light must be steady green.
Move the feed roller bar to ReVeRSe (R) when you want

the chipper push materials back out of the feed chute.
Move the feed roller bar to STOP to halt the rotation of the

feed roller.

R

REVERSE

R

F

FORWARD

STOP

REVERSE

RESET/OVERRIDE

BUTTON (WHERE

AVAILABLE)

CONTROLLER

LIGHT

FEED ROLLER

CONTROL BAR

SAFETY BAR

(WHERE

AVAILABLE)

4.4 RaISE ExTENSIoN TRaY bEFoRE

ToWING

The machine chips a variety of materials into a more

readily decomposed or handled condition. The following

guidelines will help you get started.

Run unit at full operating speed

1.

before starting to

chip material.
Limbs fed in to the chipper chute must be 8 inches

2.

(20 cm) in diameter or less. Trim side branches that

cannot be bent enough to feed into the chipper chute.

hold small diameter branches together in a bundle and

feed in simultaneously.
Exclude pieces of metal, rocks, bottles, cans, and

3.

other foreign objects when feeding material into the

machine.
Feed brush from the side of the chipper chute,

4.

rather

than from the front. Step aside to avoid being hit by the

brush moving into the chipper.
place limb, butt end first, into the chipper chute

5.

until it contacts the chipper blades. The actual feed

rate of the limb into the chipper will depend on the type

of material fed and sharpness of the cutting blades.
If the engine slows to where it may stall,

6.

stop feeding

material and allow the engine to recover. Feed material

more evenly.
If the chipper jams,

7.

remove the branch and rotate it

before reinserting it into the chute. Alternately insert

and retract the limb or insert continuously at a rate that

will not kill the engine.
do not use the clutch to clear a plugged rotor.

8.

This

may cause belt damage. Refer to the instructions for

clearing a plugged rotor in the Service and Maintenance

section.
alternate greener material with dry material

9.

to

lubricate the chipping blades for longer life and better

performance. chipping dead, dry material will create

heat and dull the chipping blades quickly.
Sharpen the chipping blades periodically.

10.

check

the sharpness of the blades every 5-15 hours. Refer

to the Service and Maintenance section for sharpening

instructions.

euROPeAN MOdelS ONlY
push the Safety bar in the event of an emergency and

forward feed will stop. Push the reset/override button to

resume forward feed after returning the safety bar to its

normal operating position.
upon start-up, the controller light will glow a steady red.

Push the reset/override button to reset.
If false trips occur, the reset button can be held in for 5

Raise the extension tray to an upright position before

towing the machine. Secure with the fastener located near

the top of the chute.
If your model is equipped with a safety bar, once the

extension tray is in an upright position, push the safety bar

down to lock the bar. To unlock, lower the extension tray

and push in the safety bar.

This manual is related to the following products: