JLG 1250AJP Parts Manual - Manual (Page 215)

SECTION 3 - BOOM
3121172 1250AJP 215
FIGURE 3-4. ACTUATOR ASSEMBLIES
ITEM PART NUMBER QTY DESCRIPTION REV
Ref ACTUATOR ASSEMBLIES
Ref Platform Rotate
See Notes 1 AND 2 Ref Platform Rotate (See Notes 1 & 2) (was 2-Port Design p/n
0060063) (Prior to SN 0300119708) F
1001097643 Ref Platform Rotate (3-Port Design) (SN 03000119708 to Present) A
Ref Jib Rotate
See Notes 1 AND 3 Ref Jib Rotate (See Notes 1 & 3) (was 2-Port Design p/n 0060064)
(Prior to SN 0300119708) I
1001097619 Ref Jib Rotate (3-Port Design) (SN 03000119708 to Present) A
Ref Note 1: Verify Motion Control Valve Design Before Ordering
Parts.
Ref Note 2: Platform Rotator - 2-Port Motion Control Valve
Platform Rotator no longer available. Must upgrade to 3-Port
design. Purchase Rotator p/n 1001097643, Rotator Service
Replacement Kit p/n 1001097785, and Jib Rotator Motion
Control Valve p/n 70002859.
Ref Note 3: Jib Rotator - 2-Port Motion Control Valve Jib Rotator
no longer available. Must upgrade to 3-Port design.
Purchase Rotator p/n 1001097619, Rotator Service
Replacement Kit p/n 1001097785, and Platform Rotator
Motion Control Valve p/n 70001639.
1 See Note 1 Case/Bracket Weldment (Note: Not Available - Purchase
Complete Assembly)
2 Ref Shaft Options:
2 7017162 1 0060063 & 1001097643 Platform Rotator
2 7017191 1 0060064 & 1001097619 Jib Rotator
3 Ref Sleeve, Piston Options:
3 7017163 1 0060063 & 1001097643 Platform Rotator
3 7017187 1 0060064 & 1001097619 Jib Rotator
4 Ref Cap, End Options:
4 7017164 1 0060063 & 1001097643 Platform Rotator
4 7017188 1 0060064 & 1001097619 Jib Rotator
5 See Note AR Screw (Note: See Item 53 for Replacement Options)
See Note AR Dowel Pin (Note: See Item 53 for Replacement Options)
20 See Note 1 Seal, Rod (Note: See Item 51 for Replacement Options)
22 See Note 1 Seal, Piston (Note: See Item 51 for Replacement Options)
24 See Note 1 Seal, Cap (Note: See Item 51 for Replacement Options)
25 See Note 2 Packing, Bearing (Note: See Item 51 for Replacement Options)
27 See Note 1 Ring, Cap Back-Up (Note: See Item 51 for Replacement Options)
31 See Note 2 Seal (Note: See Item 51 for Replacement Options)
32 See Note 2 Bearing, Shaft (Note: See Item 52 for Replacement Options)
34 See Note 2 Thrust Washer (Note: See Item 52 for Replacement Options)
41 Ref Motion Control Valve Assembly Options (Cartridges not serviced
separately.):
41 See Note 1 0060063 Platform Rotator (was 2-Port Design p/n 7017172)
41 70001639 1 1001097643 Platform Rotator
41 See Note 1 0060064 Jib Rotator (was 2-Port Design p/n 7017190)
41 70002859 1 1001097619 Jib Rotator (was p/n 70001641)
Ref Note: 2-Port Design Motion Control Valves no longer
available. Must upgrade to 3-Port design. Purchase
Platform Motion Control Valve p/n 70001639, Jib Motion
Control Valve p/n 70002859, and Rotator Service
Replacement Kit p/n 1001097785.