Aries Automotive TB45-5005 - Manual (Page 2)

Page 2 of 5
For models without tow hooks:
A. Select one of the Upper Frame Brackets and the driver side Lower Frame Mounting Bracket.
Bolt the two together with (2) 12mm Flat Washers, (2) 12mm Lock Washers and (2) 12mm Hex
Nuts. NOTE: On some vehicles, it may be easier to assemble the two-piece bracket on the
vehicle, (Figure 3). Snug the hardware but do not tighten at this time.
B. Remove the hex nuts on the two lower factory bumper bolts, (Figure 2A). Insert the
assembled Mounting Bracket up from behind the bumper and align the holes in the Mounting
Bracket with the bumper bolts. Attach the Bracket to the bumper bolts using the factory hex nuts
and tighten this hardware only.
For models with tow hooks:
A. Remove the (2) hex nuts holding the front of the tow hook to the back of the bumper.
Select the driver side Lower Mounting Bracket and hang it from the tow hook mounting studs,
(Figure 2B). Attach the Lower Mounting Bracket to the two studs using the factory Hex Nuts.
Snug the hardware but do not tighten at this time.
4. Repeat step 3 for the passenger side bracket installation.
5. With help, position the Bull Bar on the inside of the Mounting Brackets. Use the included (4) 12-
1.75mm x 35mm Hex Head Bolts, (4) 12mm Lock Washers, (8) 12mm Flat Washers, and (4) 12-
1.75mm Hex Nuts to attach the Bull Bar to the Mounting Brackets, (Figure 3). Snug but do not
tighten hardware.
6. Stand back from the vehicle and check to see that the Bull Bar is centered and level on the vehicle
and adjust as necessary. Tighten only the hardware securing the Mounting Brackets to the truck.
Do not tighten the hardware on the Bull Bar. Remove the Bull Bar.
7. Hold the splash guard up to the bumper cover and align it with the mounting points. Mark the
location of the Mounting Brackets onto the back of the splash guard, (Figure 4). Measure the
Brackets and the location of the mounting points before cutting to double check the location
marked to cut, (Figure 5). Cut an approximately 1/2" wide by 4" long slot in the splash guard as
pictured in Figure 6. NOTE: The size of the slot is an estimate only and may vary due to different
factory designs of splash guards and front bumper covers. Also, additional cutting may be
required to clear the Support Bracket on vehicles equipped with tow hooks. Hold the Support
Bracket in location to check for clearance and cut as required. IMPORTANT: To maintain the
integrity of the splash guard, do not cut the slot any larger than necessary. It is recommended to
make several small cuts and check the fit often for a clean installation.
8. Once the final cuts have been made, reinstall the splash guard using the factory hardware. Use
the included (2) 6mm x 20mm Allen Bolts, (4) 6mm Flat Washers and (2) 6mm Hex Nuts to
replace the rivets if required, (Figure 7).
9. Install the Support Brackets.
A. For vehicles without tow hooks. Install the driver side Support Bracket with the slotted side
toward the front of the truck. Bolt the Bracket to the inside of the Lower Mount using the round
hole above the two slotted holes in the Bracket. Use the included (1) 10mm x 35mm Hex Bolt, (2)
10mm Flat Washers, (1) 10mm Lock Washer and (1) 10mm Hex Nut, (Figure 8A). Attach the rear
of the Support Bracket to the frame with (1) 12-1.5mm x 30mm Fine Thread Hex Bolt, (1) 12mm
Flat Washer and (1) 12mm Lock Washer. IMPORTANT: The hole in the bottom of the frame is
fine thread. Only use the 12-1.5mm x 30mm Hex Bolt provided in the hardware kit. Repeat this
step for the passenger side Support Bracket. Snug but do not tighten all hardware at this time.
B. For vehicles with tow hooks. Install the driver side Support Bracket with the round hole
toward the front of the truck and the slotted hole to the rear. Bolt the slotted end of the Support
Bracket to the rear mounting bolt for the tow hook. Loosen the factory hex bolt and insert the
slotted end of the Support Bracket under the head of the factory bolt, (Figure 8B).
Do not bolt the front of the Support Bracket to the inside of the Lower Mounting Bracket at this
time. Repeat this step for the passenger side Support Bracket. Snug but do not tighten all
hardware at this time.