Toshiba DVR20 - Manual (Page 35)

35 EN
In
tr
od
uct
ion
Con
n
ec
ti
on
s
P
la
yb
ac
k
E
d
it
ing
Ot
he
rs
Fu
nct
ion
S
e
tu
p
Recor
d
ing
VCR Fun
ct
ions
Basi
c Se
tu
p /
TV
Vi
ew
Op
eration
1
Press [TIMER SET] to cancel the timer-standby
mode.
2
Press [TIMER PROG.].
“Timer Programming” list will appear.
3
A) To delete the timer programme:
1) Select the programme you want to delete using
[K \ L], then press [ENTER\OK].
2) Select “Delete” using [K \ L], then press
[ENTER \OK].
Confirmation window will appear.
3) Select “Yes” using [K \ L], then press [ENTER\OK].
B) To correct the timer programme:
1) Select the programme you want to correct using
[K \ L], then press [ENTER\OK].
2) Select “Programme Change” using [K \ L], then press
[ENTER \OK].
3) Correct the timer programme by using [K \ L \ 0 \ 1],
then press [ENTER \OK].
4
Press [TIMER PROG.] to exit.
5
Press [TIMER SET] to return to the timer-
standby mode.
To check the timer programming in progress
Press [TIMER PROG.].
Note
• For EPG timer recording, you can only correct the “REC To”,
“Mode” and “STTL”.
• If a timer recording is proceeding, that programme is
highlighted in red. In such a case, you cannot select any
other programmes.
• When you check the timer programming in progress by
pressing [TIMER PROG.] during operations of the
component (DVD or VCR) which is not currently used for the
timer recording, the programme will not be highlighted. In
this case, you cannot select other programmings.
On the front panel:
Press [STOP C].
On the remote control:
1
Press [STOP C].
2 Select “Yes” using [K \ L], then press
[ENTER \OK].
The error number appears on “Timer Programming” list.
The error programme will be displayed in grey with an error
number.
The error numbers indicate:
• The error programme will be deleted once you check the
error in the programme list, or once you cancel the timer-
standby mode and re-enter it.
• If there is a power failure or the unit is unplugged for more
than 30 seconds, the clock setting and all timer settings will
be lost.
• If there is no disc or an unrecordable disc in the tray
(finalised DVD-RW/-R, finalised DVD+R, a fully recorded
disc, etc.), the DVD on the front panel display will flash and
the timer recording will not occur. Insert a recordable disc.
• If there is no tape or a tape with a record tab is not in the
cassette compartment, the VCR on the front panel display
will flash and the timer recording cannot be performed.
Please insert a recordable tape.
• After all timer recordings have completed, if you want to play
back or eject the recorded disc, press [TIMER SET], and
then press [PLAY B] or [OPEN
\CLOSE A].
• The timer recording cannot be performed in DVD and VCR
at the same time. If you set two programmings with the same
channel and time both in DVD and VCR, the programming
that has priority will be recorded.
• You cannot make any DVD operation during DVD timer
recording.
• You cannot make any VCR operation during VCR timer
recording.
• Timer recording whose recording time exceeds 12 hours
cannot be made.
• When 2 or more programmes are overlapped, “Timer
programme overlapped” appears, and the overlapped
programme will be displayed in blue. To correct the timer
programme refer to “Checking, Cancelling or Correcting the
Timer Programming Information” on this page.
Checking, Cancelling or Correcting the
Timer Programming Information
Stop the Timer Recording in Progress
If the Timer Programming did not
Complete Correctly
1/1
E40 17/05 7:00 9:00 1 BBC1
17/05 10:00
Date Start End CH
Timer Programming
STTL
PDC
MON
New Programme
E1–E22, E37–E39 Recording error
E23–E24 Unrecordable disc
E25/E51 • Copy prohibited programme
• Cannot record because of the NTSC /
PAL-60 signal is received.
E26–E28 Copy prohibited programme
E29 Disc protected
E30 Disc full
E31 Already recorded 99 titles (video mode)
E32 Already recorded 99 titles (VR mode)
E33 Already recorded 999 chapters
E34 No space for Control Information
E35 PCA (Power Calibration Area) full
E36 Already finalised video format disc
E40 • There are some unrecorded parts due
to the overlapped timer programmes.
• Recording did not start at the start
time.
E41 Power failure
E42 No disc
E43 Already 49 titles recorded (+VR mode)
E44 Already 254 chapters recorded
(+VR mode)
E45 Copy prohibited programme
E46 It is impossible to record additionally on
a disc recorded by other units when
setting “Make Recording Compatible” to
“OFF”. (+VR mode)
Notes for the Timer Recording
E9TK4BD_EN.book Page 35 Wednesday, January 6, 2010 10:05 PM