Pioneer SC-1223-S - Manual (Page 81)

81
11
The Advanced MCACC menu
2 Select the setting you want to adjust.
If you’re doing this for the first time, you might want to make these settings in order.
! Fine Channel Level – Make fine adjustments to the overall balance of your speaker system (see Fine Channel
Level on page 81 ).
! Fine SP Distance – Make precise delay settings for your speaker system (see Fine Speaker Distance on page
81 ).
! Standing Wave – Control overly resonant low frequencies in your listening room (see Standing Wave on
page 81 ).
The last two settings are specifically for customizing the parameters explained in Acoustic Calibration EQ Adjust
on page 81 :
! EQ Adjust – Manually adjust the frequency balance of your speaker system while listening to test tones (see
Acoustic Calibration EQ Adjust on page 81 ).
! EQ Professional – Calibrate your system based on the direct sound coming from the speakers and make
detailed settings according to your room’s reverb characteristics (see Acoustic Calibration EQ Professional
on page 82 ).
Fine Channel Level
! Default setting: 0.0dB (all channels)
You can achieve better surround sound by properly adjusting the overall balance of your speaker system. You can
adjust the Channel Level of each speaker in 0.5 dB increments. The following setting can help you make detailed
adjustments that you may not achieve using the
Manual speaker setup on page 86 .
1 Select ‘Fine Channel Level’ from the Manual MCACC setup menu.
The volume increases to the 0.0 dB reference level.
2 Adjust the level of the left channel.
This will be the reference speaker level, so you may want to keep the level around 0.0dB so that you’ll have plenty
of room to adjust the other speaker levels.
! After pressing ENTER, test tones will be output.
3 Select each channel in turn and adjust the levels (+/–12.0 dB) as necessary.
Use k/l to adjust the volume of the speaker you selected to match the reference speaker. When it sounds like
both tones are the same volume, press j to confirm and continue to the next channel.
! For comparison purposes, the reference speaker will change depending on which speaker you select.
! If you want to go back and adjust a channel, simply use i/j to select it.
4 When you’re finished, press RETURN.
You will return to the Manual MCACC setup menu.
Fine Speaker Distance
! Default setting: 3.00 m (all speakers)
For proper sound depth and separation with your system, it is necessary to add a slight bit of delay to some
speakers so that all sounds will arrive at the listening position at the same time. You can adjust the distance of
each speaker in 1 cm increments. The following setting can help you make detailed adjustments that you may not
achieve using the
Manual speaker setup on page 86 .
1 Select ‘Fine SP Distance’ from the Manual MCACC setup menu.
2 Adjust the distance of the left channel from the listening position.
3 Select each channel in turn and adjust the distance as necessary.
Use k/l to adjust the delay of the speaker you selected to match the reference speaker.
Listen to the reference speaker and use it to measure the target channel. From the listening position, face the two
speakers with your arms outstretched pointing at each speaker. Try to make the two tones sound as if they are
arriving simultaneously at a position slightly in front of you and between your arm span.
! If you can’t seem to achieve this by adjusting the distance setting, you may need to change the angle of your
speakers very slightly.
! The subwoofer’s test tone differs in tone from other channels. Adjust so that the sound of the subwoofer can
be heard distinctly. Note that when adjusting the subwoofer, depending on the low frequency response of
your speaker, it may be difficult to hear the change even when the setting is increased or decreased or when
the position of the speaker is changed. Note that it may be difficult to compare this tone with the other speak-
ers in your setup (depending on the low frequency response of the reference speaker).
When it sounds like the delay settings are matched up, press j to confirm and continue to the next channel.
! For comparison purposes, the reference speaker will change depending on which speaker you select.
! If you want to go back and adjust a channel, simply use i/j to select it.
4 When you’re finished, press RETURN.
You will return to the Manual MCACC setup menu.
Standing Wave
! Default setting: ON/ATT 0.0dB (all filters)
Acoustic standing waves occur when, under certain conditions, sound waves from your speaker system resonate
mutually with sound waves reflected off the walls in your listening area. This can have a negative effect on the
overall sound, especially at certain lower frequencies. Depending on speaker placement, your listening posi-
tion, and ultimately the shape of your room, it results in an overly resonant (‘boomy’) sound. The Standing Wave
Control uses filters to reduce the effect of overly resonant sounds in your listening area. During playback of a
source, you can customize the filters used for Standing Wave Control for each of your MCACC presets.
! Standing Wave control filter settings cannot be changed during playback of sources using the HDMI
connection.
1 Select ‘Standing Wave’ from the Manual MCACC setup menu.
2 Adjust the parameters for the Standing Wave Control.
! Filter Channel – Select the channel to which you will apply the filter(s): MAIN (all except center channel and
subwoofer), Center or SW (subwoofer).
! TRIM (only available when the filter channel above is SW) – Adjust the subwoofer channel level (to compen-
sate for the difference in output post-filter).
! Freq / Q / ATT – These are the filter parameters where Freq represents the frequency you will be targeting
and Q is the bandwidth (the higher the Q, the narrower the bandwidth, or range) of the attenuation (ATT, the
amount of reduction to the targeted frequency).
3 When you’re finished, press RETURN.
You will return to the Manual MCACC setup menu.
Acoustic Calibration EQ Adjust
! Default setting: ON/0.0dB (all channels/bands)
Acoustic Calibration Equalization is a kind of room equalizer for your speakers (excluding the subwoofer). It works
by measuring the acoustic characteristics of your room and neutralizing the ambient characteristics that can
color the original source material (providing a ‘flat’ equalization setting). If you’re not satisfied with the adjust-
ment provided in
Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37 or Automatic
MCACC (Expert) on page 79 , you can also adjust these settings manually to get a frequency balance that suits
your tastes.