Pioneer DEH-X5500BT - Manual (Page 18)

When you do not want low sounds from the subwoo-
fer output frequency range to play from the front or
rear speakers, turn on the HPF (high pass filter). Only
frequencies higher than those in the selected range
are output from the front or rear speakers.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the following:
Cut-off frequency —Slope level
3 Turn M.C. to select the desired setting.
Cut-off frequency: OFF —50HZ—63HZ—80HZ—
100HZ —125HZ—160HZ—200HZ
Slope level: –6— –12
SLA (source level adjustment)
SLA (Source level adjustment) lets you adjust the vo-
lume level of each source to prevent radical changes
in volume when switching between sources.
! Settings are based on the FM volume level, which
remains unchanged.
! The MW/LW volume level can also be adjusted
with this function.
! When selecting FM as the source, you cannot
switch to SLA.
! USB and iPod are all set to the same setting auto-
matically.
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the source volume.
Adjustment range: +4 to –4
System menu
Important
PW SAVE (power saving) is canceled if the vehi-
cle battery is disconnected and will need to be
turned back on once the battery is reconnected.
When
PW SAVE (power saving) is off, depending
on connection methods, the unit may continue to
draw power from the battery if your vehicle
’s igni-
tion doesn
’t have an ACC (accessory) position.
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select SYSTEM.
3 Turn M.C. to select the system menu
function.
Once selected, the following system menu
functions can be adjusted.
! INFO DISPLAY is not available for DEH-
4500BT.
LANGUAGE (multi-language)
This unit can display the text information from a com-
pressed audio file even for information embedded in
English or Russian.
! If the embedded language and the selected lan-
guage setting are not the same, text information
may not display properly.
! Some characters may not be displayed properly.
1 Turn M.C. to select the desired setting.
ENG (English) —РУС (Russian)
CLOCK SET (setting the clock)
1 Press M.C. to display the setting mode.
2 Press M.C. to select the segment of the clock dis-
play you wish to set.
Hour
—Minute
3 Turn M.C. to adjust the clock.
12H/24H (time notation)
1 Press M.C. to select the desired setting.
12H (12-hour clock) —24H (24-hour clock)
INFO DISPLAY (sub information)
The type of text information displayed in the sub infor-
mation section can be toggled.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
SPEANA —LEVEL METER—SOURCE—CLOCK—
OFF
! The signal bar indicator displays for SPEANA or
LEVEL METER when the source is set to TUNER.
AUTO PI (auto PI seek)
The unit can automatically search for a different sta-
tion with the same programming, even during preset
recall.
1 Press M.C. to turn Auto PI seek on or off.
AUX (auxiliary input)
Activate this setting when using an auxiliary device
connected to this unit.
1 Press M.C. to turn AUX on or off.
BT AUDIO (Bluetooth audio activation)
You need to activate the BT AUDIO source in order to
use a Bluetooth audio player.
1 Press M.C. to turn the BT AUDIO source on or off.
PW SAVE (power saving)
Switching this function on enables you to reduce the
consumption of battery power.
! Turning on the source is the only operation al-
lowed when this function is on.
1 Press M.C. to turn the power save on or off.
En
18
Section
02 Operating this unit