Pioneer PDP-506XDE - Manual (Page 61)

61
En
Enjoying through External Equipment 13
En
gl
is
h
Using HDMI Input
This Plasma Display System is equipped with two HDMI
terminals (INPUT 3 and 4) which accept digital video and audio
signals. To use the HDMI terminal, activate the terminal and
specify the types of video and audio signals to be received from
the connected equipment. For the types of these signals, see
the operation manual that came with the connected
equipment.
Before starting the menu, press INPUT 3 or INPUT 4 on the
remote control unit or press INPUT on the Media Receiver to
select INPUT 3 or INPUT 4.
For audio, the system supports the following:
• Linear PCM (STEREO 2ch)
• Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz
NOTE
• PC signals are out of correspondence.
Connecting HDMI equipment
When using the INPUT 3 HDMI terminal:
When using the INPUT 4 HDMI terminal:
To activate the HDMI terminal:
When you use the INPUT 3 HDMI terminal, use the following
procedure to activate the terminal.
1
Press HOME MENU.
2
Select “Option” ( / then ENTER).
3
Select “HDMI Input” ( / then ENTER).
4
Select “Setting” ( / then ENTER).
5
Select “Enable” ( / then ENTER).
6
Press HOME MENU to exit the menu.
NOTE
• You need not activate the INPUT 4 HDMI terminal; you
cannot manually deactivate this terminal.
To specify the type of digital video signals:
1
Repeat steps 1 to 3 provided for “ To activate the HDMI
terminal.”
2
Select “Video” ( / then ENTER).
3
Select the type of digital video signals ( / then ENTER).
• If you select “Auto”, an attempt will be made to identify
the type of digital video signals when digital video
signals are received.
4
Press HOME MENU to exit the menu.
Input signal correlation table
1920*1080i@50Hz
720*576p@50Hz
1280*720p@50Hz
720(1440)*576i@50Hz
1920*[email protected]/60Hz
720*[email protected]/60Hz
1280*[email protected]/60Hz
720(1440)*[email protected]/60Hz
1920*1080p@24Hz
INPUT 1
INPUT 1
CONTROL SERVICE ONLY I N O U T
ANT i /o link.A
SELECT
INPUT 2 3
INPUT 3 HDMI HDMI
SYSTEM CABLE
ANT(DIGITAL) IN OUT OPTICAL DIGITAL OUT COMMON INTERFACE
INPUT 2
COMPONENT VIDEO
Y
AUDIO OUTPUT
INPUT 4
R-AUDIO-L SUB WOOFER P B P R
BLACK WHITE
Media Receiver (rear view)
HDMI cable
(commercially
available.)
SCART cable
(commercially available.)
Connect the SCART cable only
when inputting analogue audio
signals.
HDMI equipment
Item Description
Disable
(factory default) Deactivates the HDMI terminal.
Enable Activates the HDMI terminal.
Item Description
Auto
(factory default) Automatically identifies input digital video signals.
Colour-1 Digital Component Video signals (4:2:2) locked
Colour-2 Digital Component Video signals (4:4:4) locked
Colour-3 Digital RGB signals locked
INPUT 1
INPUT 1
CONTROL SERVICE ONLY I N O U T
ANT i /o link.A
SELECT
INPUT 2 3
INPUT 3 HDMI HDMI
SYSTEM CABLE
ANT(DIGITAL)
IN OUT OPTICAL DIGITAL OUT COMMON INTERFACE
INPUT 2
COMPONENT VIDEO
Y
AUDIO OUTPUT
INPUT 4
R-AUDIO-L SUB WOOFER P B P R
BLACK WHITE
Media Receiver (rear view)
HDMI equipment
HDMI cable
(commercially
available.)
PDP506XDE.book Page 61 Friday, June 17, 2005 3:08 PM