Pioneer X-HM20DAB-K - Manual (Page 26)

11/8/11 X-HM10_20_DAB_En.fm
En-26
Troubleshooting chart (continued)
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet (CD pickup, etc.) or on the transmitter
on the remote control. Condensation can cause the unit to
malfunction. If this happens, leave the power on with no
disc in the unit until normal playback is possible (about 1
hour). Wipe off any condensation on the transmitter with a
soft cloth before operating the unit.
When this product is subjected to strong external
interference (mechanical shock, excessive static
electricity, abnormal supply voltage due to lightning, etc.)
or if it is operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on
again.
2 If the unit is not restored in the previous operation, unplug
and plug in the unit again, and then turn the power on.
Note:
If neither operation above restores the unit, clear all the
memory by resetting it.
Caution:
This operation will erase all data stored in memory
including clock, timer settings, tuner preset, and CD
programme.
Remove the iPod, USB memory device and disc from the
unit. Then, set the unit to the power stand-by mode.
Carrying the unit with iPod or USB memory device left
docked or discs left inside might damage the unit.
Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on
the disc surface. Follow the guidelines below for maximum
enjoyment from your CD collection and player.
l
Do not write on either side of the disc, particularly the
non-label side from which signals are read. Do not
mark this surface.
l Keep your discs away from direct sunlight, heat, and
excessive moisture.
l Always hold the CDs by the edges. Fingerprints, dirt, or
water on the CDs can cause noise or mistracking. If a
CD is dirty or does not play properly, clean it with a soft,
dry cloth, wiping straight out from the centre, along the
radius.
Maintenance
Periodically wipe the cabinet with a soft cloth and a diluted
soap solution, then with a dry cloth.
Caution:
l Do not use chemicals for cleaning (petrol, paint thinner,
etc.). It may damage the cabinet.
l Do not apply oil to the inside of the unit. It may cause
malfunctions.
n iPod and iPhone (X-HM20DAB only)
Symptom Possible cause
l No sound is
produced.
No image
appears on the
TV/monitor.
l The iPod or iPhone is not playing.
l The iPod or iPhone is not
properly connected to the unit.
l Is the AC power lead of the
unit plugged in?
l The video cable is not properly
connected.
l The TV/monitor’s input
selection is not properly set.
l The iPod TV out feature has
not been set to output video.
l Audio from the iPod/iPhone cannot
be heard via the headphones
connected to the unit.
l iPod or iPhone
will not charge.
l The iPod or iPhone is not
making full contact with the
connector.
l Using iPod (3 rd generation).
l The iPod or iPhone is not
supported. Refer to page 10
for compatible models.
l The iPod or iPhone unit cannot
be charged whilst the main unit
is in USB mode.
l “This accessory is
not made to work
with iPhone” or
“This accessory is
not supported by
iPhone” appears
on iPhone screen.
l The iPhone battery is low.
Please charge the iPhone.
l iPhone is not properly docked.
n Condensation
n If problem occurs
n Factory reset, clearing all memory
1 Press the STANDBY/ON button to turn the power on.
2 Press the LINE button button on the remote control or
INPUT button repeatedly on the main unit to select
LINE IN function.
3 In LINE IN function, press the button on the
main unit press and hold the button until "RESET"
appears.
n Before transporting the unit
n Care of compact discs
n Cleaning the cabinet
NO YES
Correct