American Standard Cadet Corner Whirlpool and Bathing Pool 2775.018WC - Manual (Page 2)

H54
© 2008 AS America Inc.
15
24
m
m
(6
0)
70mm REF.
(2-3/4)
165mm
(6-1/2)
279mm
(11)
RECOMMENDED
FITTING LOCATION
64 X 330mm (2-1/2 X 13)
229 X 305mm
(9 X 12)
CUTOUT IN
FLOOR FOR
DRAIN
PROVIDE ACCESS
TO PUMP FOR
SERVICING ON ALL
INSTALLATIONS
OUTLINE OF
CUTOUT
2159mm
(85)
1080 mm
(42-1/2)
C/L
1524mm
(60)
1076mm
(42-3/8)
1080mm
(42-1/2)
PUMP
C/L OF
DRAIN OUTLET
1-1/2 O.D. TAILPIECE
LEVELING STRINGER
NOT FOR SUPPORT
70mm
(2-3/4)
117mm
(4-5/8)
1-1/2 N.P.T.M.
THREADS
38 mm REF.
(1-1/2)
C/L OF
OVERFLOW 76mm
(3)
464mm
(18-1/4)
502mm
(19-3/4)
ROUGH
FLOOR
INTEGRAL
SUPPORT
FEET
INTEGRAL
FEET
15
24
m
m
(6
0)
70mm REF.
(2-3/4)
165mm
(6-1/2)
279mm
(11)
RECOMMENDED
FITTING LOCATION
64 X 330mm (2-1/2 X 13)
229 X 305mm
(9 X 12)
CUTOUT IN
FLOOR
FOR
DRAIN
OUTLINE OF
CUTOUT
2159mm
(85)
1080 mm
(42-1/2)
C/L
1524mm
(60)
1076mm
(42-3/8)
C/L OF
DRAIN OUTLET
1-1/2 O.D. TAILPIECE
LEVELING STRINGER
NOT FOR SUPPORT
70mm
(2-3/4)
117mm
(4-5/8)
1-1/2 N.P.T.M.
THREADS
38 mm REF.
(1-1/2)
C/L OF
OVERFLOW 76mm
(3)
464mm
(18-1/4)
502mm
(19-3/4)
ROUGH
FLOOR
85 X 60 X 19-3/4In.(2159 X 1524 X 502mm)
130 Lbs. (59 Kg.)
756 Lbs. (343 Kg.)
75 Gal. (284 L.)
60 Gal. (227 L.)
32 X 32 In. (813 mm X 813 mm)
46 X 46 In. (1168 X 1168mm)
14 In. (356 mm)
34 Lbs./Sq. Ft. (115 Kgs/Sq. m.)
41.7
70.4
GENERAL SPECIFICATIONS FOR 2775 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
2.1 HP, 14.4 AMPS, 120V. SYSTEM I PUMP
85 X 60 X 19-3/4In.
(2159mm X 1524 mm X 502mm)
105 Lbs. (48 Kg.)
730 Lbs. (328 Kg.)
75 Gal. (284 L.)
32 X 32 In. (813 mm X 813 mm)
46 X 46 In. (1168 X 1168mm)
14 In. (356 mm)
33 Lbs./Sq. Ft. (111 Kgs/Sq. m.)
41.7
70.4
GENERAL SPECIFICATIONS FOR 2775 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP OF
BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL 2 WALL TILING BEAD KIT AVAILABLE AND MUST BE ORDERED SEPARATELY.
● FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING
SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1/A112.19.7M.
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.
Revised 2/08
CADET™ CORNER
WHIRLPOOL AND BATHING POOL
HIGH GLOSS