HOUNO K & C - Manual (Page 18)

C & K – ver. 3.x – August 2009
18
Error Codes
Error code 3: GENRA HOT
Generator too hot (Generator thermoswitch has tripped. Reconnect
by pressing button under oven.)
Error code 4: OVEN HOT
Oven too hot (Oven chamber thermoswitch has tripped. Reconnect
by pressing button under oven.)
Error code 5: FAN HOT
Fan too hot (Thermoswitch in motor has tripped. Wait for 10
minutes and try again.
Error code 6: DRAIN > 75
Drain too hot (Drain temperature has been above 75°C for more
than 5 min. Check that jet in drain is working.)
Error code 7: OVEN SENS
Oven sensor defective (Temperature sensor in oven chamber not
working properly.)
Error code 8: PROBE SENS
Core temp. probe not connected (A program using core temp.
probe has been selected but probe has not been connected.)
Error code 9: GENER SENS
Generator sensor defective (Temperature sensor in generator not
working.)
Error code 10: DRAIN SENS
Drain sensor defective (Sensor in drain not working. Oven can still
be used.)
Error code 11: WATER SHOR
Water shortage (Steam generator was not filled within two minutes.
Check that the water has been turned on.)
Error code 12: SSR HOT SSR too hot (Solid-state relay too hot.)
Error code 13: GENER > 130
Generator too hot (Temperature in steam generator higher than
130°C. If fault recurs, descale generator)
Error code 14: FAN SPEED Fan running too slow
Error code 15: CPU HOT CPU board too hot (> 60°C)
Error code 16: IO BRD HOT IO board too hot (> 60°C)
Error code 18: DATA ERROR Error in set-up data
Error code 19: WRONG LANG Wrong language
Error code 20: NO COM IO
Internal defect (Failure in communication between computer and IO
board.)
Error code 22: NO RESTART Restart not possible (Oven has been without power too long.)
Error code 23: OVEN WARM Oven too hot at CombiWash start-up
Error code 24: DRAIN ERR
Draining failure (Drain blocked or failure of drain pump. Water level
in generator still high after 10 seconds of draining.)
Error code 25: PROBE ERR
Core temperature probe defective (1, 2 or 3 of the elements in
the core temperature probe defective.)
Error code 28: ALARM ERR Configuration error in main alarms (3, 4, 5, 12) (warning)
Error code 29: DOOR SENS Wrong door sensor signal (warning)
Error code 34: WATER PRES Water pressure too low (Check that water is turned on.)
Error code 40: IO BRD HOT Temperature in IO board critical (Warning after program run.)
Error code 43: WRONG SW Wrong software version (Visual Cooking I oven)
Error code 44: DAMPER ERR Failure during initialisation of exhaust at oven start-up
Error code 45: 24 V ERROR 24 V missing or failure of main contactor output
Error code 50 SWITCH ON
Pressure switch on when gas-air control unit not running
(timeout 20 sec.)
Error code 51 SWITCH OFF
Pressure switch not on when gas-air control unit running
(timeout 20 sec.)
Error code 52 GAS VALVE
Gas valve does not open (automatic gas burner control has failed
(timeout 20 sec.))
Error code 53 NO FAN RPM
Gas-air control unit does not revolve when pressure switch is
on
Error code 54 FAN ERROR
Gas-air control unit does not run at correct RPM just before
ignition
Error code 55 GAS FAIL Warning: Ignition failed
Error code 56 GAS ERROR Flame fails to occur after 3 attempts
Error code 57 GAS STOP Warning: Gas failure during operation