CatEye CC-RD300W [Strada Wireless] User Manual

Cateye strada wireless, Cyclocomputer cc-rd300w

Tire circumference

reference table

12 x 1.75
14 x 1.50
14 x 1.75
16 x 1.50
16 x 1.75
18 x 1.50
18 x 1.75
20 x 1.75
20 x 1-3/8
22 x 1-3/8
22 x 1-1/2
24 x 1
24 x 3/4 Tubular
24 x 1-1/8
24 x 1-1/4
24 x 1.75
24 x 2.00
24 x 2.125
26 x 7/8
26 x 1(59)
26 x 1(65)
26 x 1.25
26 x 1-1/8
26 x 1-3/8
26 x 1-1/2
26 x 1.40
26 x 1.50
26 x 1.75
26 x 1.95
26 x 2.00
26 x 2.10
26 x 2.125
26 x 2.35
26 x 3.00
27 x 1
27 x 1-1/8
27 x 1-1/4
27 x 1-3/8
650 x 20C
650 x 23C
650 x 35A
650 x 38A
650 x 38B
700 x 18C
700 x 19C
700 x 20C
700 x 23C
700 x 25C
700 x 28C
700 x 30C
700 x 32C
700C Tubular
700 x 35C
700 x 38C
700 x 40C
29 x 2.1
29 x 2.3

935

1020
1055
1185
1195
1340
1350
1515
1615
1770
1785
1753
1785
1795
1905
1890
1925
1965
1920
1913
1952
1953
1970
2068
2100
2005
2010
2023
2050
2055
2068
2070
2083
2170
2145
2155
2161
2169
1938
1944
2090
2125
2105
2070
2080
2086
2096
2105
2136
2146
2155
2130
2168
2180
2200
2288
2326

Tire size

L (mm)

CATEYE STRADA WIRELESS

CYCLOCOMPUTER CC-RD300W

U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending
Copyright© 2011 CATEYE Co., Ltd.
CCRD3W-110930 066600542 6

L mm

SEN

SOR

ZONE

5 mm

SENSO

ZONE

Install the sensor and magnet

Sensor zone

Inside of right front fork

Max

70 cm

YES!

NO!

The distance between the computer
and the sensor must not exceed the
transmission range of 70 cm. The back
of the computer must face the sensor.

The magnet
must pass
through the
sensor zone.

The clearance
between the
sensor surface
and the magnet
must not
exceed 5 mm.

SENSOR

ZONE

SENSOR

ZONE

Click

* For wing type handlebar or oversized

stem, bracket can be mounted using
the Bracket Holder and nylon ties.
(Option)

Caution:
Make sure that the back of the computer faces the sensor.
* The computer may not function appropriately on some

stem if its back does not face the sensor as shown in

When attaching the bracket to the stem

Spoke

Toward the
sensor zone

Install the magnet

While supporting it by hand,

Handlebar

Cut

Attach the bracket to the stem or handlebar

Remove/install the
computer

Caution:
Round off the cut edge
of the bracket band to
prevent injury.

Install the sensor

Inside of right front fork

* After installation, rotate the front wheel gently to check that the speed is displayed on the

computer. If the speed is not displayed, check that conditions

, and

, above, have

been done appropriately.

Stem

Pull
securely

* Install the sensor as close to the upper

part of the front fork as possible.

push it out as if lifting the front up

When attaching the bracket to the handlebar

How to install the unit on your bicycle

1 Bracket band
2 Bracket
3

Nut

Speed sensor

5 Magnet
6 Sensor rubber pad
7 Bracket rubber pad
8 Nylon ties (x2)

ENG

Before using the computer, please thoroughly read this manual and keep it for
future reference.

WARNING / CAUTION

• Do not concentrate on the computer while riding. Ride safely!
• Install the magnet, sensor, and bracket securely. Check these periodically.
• If a child swallows a battery, consult a doctor immediately.
• Do not leave the computer in direct sunlight for unnecessary or extended periods.
• Do not disassemble the computer.
• Do not drop the computer. Doing so may result in a computer malfunction or damage.
• When using the computer installed on the bracket, change the MODE by pressing on the three dots

below the screen. Pressing hard on other areas can result in malfunction or damage to the computer.

• Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the bracket

threads.

• When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.
• Dispose of used batteries according to local regulations.
• LCD screen may be distorted when viewed through polarized sunglass lenses.

Wireless Sensor

The sensor was designed to receive signals within a maximum range of 70 cm, to reduce chance of
interference.
When adjusting the wireless sensor, note the following:

• Signals cannot be received if the distance between the sensor and the computer is too great.
• The transmission distance may be shorter due to low temperature or low battery.
• Signals can be received only when the back of the computer is facing the sensor.

Interference may occur, resulting in incorrect data, if the computer is:

• Near a TV, PC, radio, motor, or in a car or train.
• Close to a railroad crossing, railway tracks, TV stations and/or radar base.
• Using with other wireless devices in close proximity.

This device complies with Part 15 of the FCC Rules.Operation is subject to the following
two conditions:(1)This device may not cause harmful interference,and (2)this device
must accept any interference received,including interference that may cause undesired
operation.
Modifications The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by CatEye Co.,Ltd.May void the user
’s authority to operate the equipment.

MENU

MODE

MENU

MODE

MENU

MODE

MENU

MODE

km/h

↔ mph

Increase

Move digits
(by pressing
& holding)

Clear all data (initialization)

Press the AC button on the back.

Select the desired speed units

Select “

” or “

”.

Enter the tire circumference

Enter the tire circumference of your bicycle in mm.
* Refer to the tire circumference reference table.

Set the clock

When MODE is pressed and held, “Displayed
time”, “Hour”, and “Minute” will appear, in
this order.

24h

↔ 12h,

or increase
the value

Switch the
screen or
move digits
(by pressing
& holding)

Preparing the computer

Battery case cover

Push!

When the computer is
mounted on the bracket

: Speed unit

: Wheel size icon
: Sensor signal reception icon

Measure wheel circumference
(L) of your bike
To get the most accurate
calibration do a wheel roll out.
With the valve stem
perpendicular to the ground,
mark the pavement at the valve
stem. With the riders weight on
the bike, roll the wheel one tire
revolution in a straight line and
mark the ground when the
valve stem is perpendicular to
the ground again. Measure the
distance in millimeters. This is
the most accurate wheel
calibration number.