CatEye CC-CD200N - Manual

1
2
6
7
3
4
5
8
9
3
2
1
3
9 6
9
3
9
6
3
3
6
4
7
7
4
9
1
1
8
7
9
MODE
!
L(mm)
12 x1.75 935
14 x 1.50 1020
14 x 1.75 1055
16 x 1.50 1185
16 x 1.75 1195
18 x 1.50 1340
18 x 1.75 1350
20 x 1.75 1515
20 x 1-3/8 1615
22 x 1-3/8 1770
22 x 1-1/2 1785
24 x 1 1753
24 x 3/4 Tubular 1785
24 x 1-1/8 1795
24 x 1-1/4 1905
24 x 1.75 1890
24 x 2.00 1925
24 x 2.125 1965
26 x 7/8 1920
26 x 1(59) 1913
26 x 1(65) 1952
26 x 1.25 1953
26 x 1-1/8 1970
26 x 1-3/8 2068
26 x 1-1/2 2100
26 x 1.40 2005
26 x 1.50 2010
26 x 1.75 2023
26 x 1.95 2050
26 x 2.00 2055
26 x 2.10 2068
26 x 2.125 2070
26 x 2.35 2083
26 x 3.00 2170
27 x 1 2155
27 x 1-1/8 2161
27 x 1-1/4 2161
27 x 1-3/8 2169
650 x 35A 2090
650 x 38A 2125
650 x 38B 2105
700 x 18C 2070
700 x 19C 2080
700 x 20C 2086
700 x 23C 2096
700 x 25C 2105
700 x 28C 2136
700 x 30C 2170
700 x 32C 2155
700C Tubular 2130
700 x 35C 2168
700 x 38C 2180
700 x 40C 2200
L mm
SET
START/STOP
MODE
SET
OK OK
Computer Set-up
(For first use or after replacing the battery)
All Clear
Push the AC button on the backside.
* Push the AC button when using this
system for the first time and every
time the battery is replaced.
1
Set The Tire Circumference
Set the tire circumference in mm.
Note Refer to the chart shown on the right.
Setting is fixed and completed by pushing the SET button.
3
Increase the
number
Max. 2999 mm
Decrease
the number
Min. 10 mm
MODE Button
START/STOP Button
SET Button
Contact Point
Measurement Selection
Select the measurement unit, kilometer or mile, by pushing the
MODE button. Fix it by pushing the SET button.
2
Kilometer Mile
AC Button
You need to know
your tire size or the
roll out length of your
tire in MM's.
Refer to the chart below for
approximate tire lengths.
Tire size
Tire size is usually shown on
the sidewall of tires.
Basic Functions Test
Spin the rear wheel to see if Speed is reading properly. Push the mode button until Cadence
(Cdc) is in the sub-display. Spin the crank arm backwards to test if Cadence is reading properly.
When you receive a signal, tightly secure the sensor so it does not move.
Note When the computer does not indicate the speed/cadence, check the position of the
magnet and the sensor.
Mount The Bracket
Secure the cord by fastening it to the frame with zip ties at regular intervals.
Put the rubber pad 8 on the bracket 1 and secure the bracket on the handle bar with the
screw. Slide the computer into the bracket until you hear the click sound. When you need to
remove the computer, press the lever on the handlebar bracket and slide the computer
forward.
Note Allow enough wire clearance in the area marked with to insure you can turn
the handlebars all the way from side to side without pulling the wire.
4
3
Rotate the rear wheel.
Rotate the crank arm
AC Button
Preparation Complete.
(the screen will show the time measurement in this state)
* The auto mode is ON in this state.
®
ASTRALE8
Installation of the Computer on Your Bike
The computer comes with the following parts:
1 Bracket
2 Cord
3 Speed Sensor
(Long Cord)
4 Cadence Sensor
(Short Cord)
5 Sensor Rubber Pad
6 Wheel Magnet
7 Cadence Magnet
8 Bracket Rubber Pad
9 Nylon Ties (10)
1
Please read these instructions carefully before installing or
using the CAT EYE ASTRALE 8.
Please keep this manual in a safe place for future reference.
CAT EYE ASTRALE 8
CYCLOCOMPUTER CC-CD200N
E: Owner’s Manual
Rear wheel
spoke
Left chainstay
The smooth edge of the zip
tie should be on the outside
Mount the wheel magnet and speed sensor
• Mount the wheel magnet 6 on a spoke of the rear wheel so the surface of the
magnet faces the sensor.
• Mount the speed sensor 3 (long cord) on the left chainstay with nylon ties 9.
Note The nylon ties can only be used once, please install with care.
U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending
Copyright © 2002/2003 CAT EYE Co. Ltd.
CCMCD2N-030531 066600252 1
Warning
• Pay attention to the road or trail! Do not be distracted by the
computer.
• Be sure to securely mount the magnet, the sensor, and the
bracket on your bicycle. Periodically check to insure they are
mounted securely and the screws have not come loose.
• Keep batteries out of reach of small children. Dispose of batter-
ies according to local regulations.
• Avoid unnecessary prolonged exposure to the sun.
• Never attempt to disassemble the computer head.
• Don’t use thinner, benzene or alcohol to wipe the surface of the
computer. They may damage the surface of computer.
Important
Note
Important Note
Mount the magnets 6 and the sensors 3 in the appropriate positions so that the
center of each magnet 6 aligns with the marked sensor line when the rear wheel
and crank arm are rotated. The magnet should be no more than 5mm from the sensor.
Center
Marked Line
Left chainstay
2
Left Chain Stay
Inward Side of
The Crank Arm
Left Chain Stay
Mount the cadence magnet and cadence sensor.
• Mount the cadence magnet 7 on the left crank arm so that it faces the sensor.
• Secure the cadence sensor 4 (short cord) on the left chain stay with nylon ties 9.
Sensor Side
Important Note
When the crank is spinning, the center of the magnet 7 should pass in front of the sensor
4 marking line. The distance between the sensor and the magnet 7 should be within
5mm. After adjusting the magnet and sensor, secure tightly with nylon ties.
Crank Arm
Center
Marked Line
Within 5 mm
Rear wheel spoke
Adjust
Within 5 mm Adjust
Sensor Side
Lever
Slide