Panasonic SCNE5EG - Manual (Page 20)

20
VQT4U60
Sound adjustment
The following sound effects can be added to the audio
output.
1
Press [SOUND] repeatedly to select the effect.
2
Press [3, 4] to select the setting and then press
[OK].
≥ You may experience a reduction in sound quality when these
effects are used with some sources. If this occurs, turn the
sound effects off.
Clock and Timer
To make this setting, point the remote control at
the speaker unit.
This is a 24-hour clock.
1
Press [SETUP] to select “CLOCK”.
2
Press [3, 4] to set the time and then press [OK].
≥ To display the clock, press [SETUP] to select “CLOCK” and
then press [OK] once. The time is displayed for 10 seconds.
(During standby, press [DISPLAY, iPod MENU] once.)
≥ The clock is reset when there is a power failure or when the
AC mains lead is removed.
≥ Reset the clock regularly to maintain accuracy.
You can set the timer so this system turns on at a
certain time every day.
Preparation
Set the clock (l left).
∫ Setting the timer
1
Press [SETUP] repeatedly to select “TIMER ADJ”.
2
Press [3, 4] to set the starting time
(“ON TIME”) and then press [OK].
3
Press [3, 4] to set the finishing time
(“OFF TIME”) and then press [OK].
∫ Turn the timer on
1
Select the music source* 1 and set the desired
volume.
2
Press [SETUP] repeatedly to select “TIMER SET”.
3
Press [3, 4] to select “SET” and then press [OK].
≥ “ F” is displayed.
≥ To turn the timer off, select “OFF”.
4
Press [Í] to turn this system off.
≥ To display the timer settings, press [SETUP] repeatedly to
select “TIMER ADJ” and then press [OK] once.
The music source and volume will also be displayed if the
timer is turned on.
≥ During standby, if the timer is turned on, press [DISPLAY,
iPod MENU] twice to display the settings.
≥ This system can be used as normal after the timer is set,
however:
– Turn this system to standby mode before the timer start
time.
– Even if the audio source or the volume is changed, the
timer will still use the audio source and volume that was
set when the timer was turned on.
≥ If this system is having a wireless communication problem at
the set time, an electronic sound may go off instead of the
set music source. Turn this system off to stop the electronic
sound.
*1: “CD”, “FM”, “AUX”, “IPOD_DOCK” and
“IPOD_PORT” / “USB” can be set as the music source.
The sleep timer can turn this system off after a set
time.
1
Press [SLEEP] repeatedly to set the time (in
minutes) and then press [OK].
“SLEEP 30” -. “SLEEP 60” -. “SLEEP 90” -. “SLEEP 120”
^------------------------ OFF (Cancel) (------------------------b
≥ The remaining time is indicated on this system’s display
except when other operations are performed.
≥ The play timer and sleep timer can be used together. The
sleep timer always has priority.
Direct-Vocal
Surround
(D.SURROUND) “LEVEL 1”, “LEVEL 2” or “OFF”.
≥ The factory preset is “OFF”.
Preset EQ
(PRESET EQ) “HEAVY” (heavy), “SOFT” (soft),
“CLEAR” (clear), “VOCAL”
(vocal) or “FLAT” (flat/off).
≥ The factory preset is “HEAVY”.
Bass (BASS) or
Treble (TREBLE) Adjust the level (j4 to i4).
Dynamic Bass
(D.BASS) “ON D.BASS” or
“OFF D.BASS”.
≥ The factory preset is
“ON D.BASS”.
Setting the clock
Play timer
Sleep timer
SC-NE5~VQT4U60.book 20 ページ ２０１３年１月２２日 火曜日 午後１時３８分