American Standard MONTERREY 6540.175 - Manual (Page 2)

M 9 6 8 5 0 8 R E V. 1 . 3
TEST INSTALLED FAUCET
5
Remove AERATOR.
Turn VALVES (1) to off position.
Insert ADAPTOR (8) with larger diameter
over the VALVE STEM (4).
Align LEVER (2) or WRIST BLADE
HANDLE (3) and install onto VALVE
STEM (4).
Insert BLUE INDEX (5) into
cold valve (right side) and red
INDEX (6) into hot valve (left
side).
Insert HANDLE SCREW (7) into
HANDLES and tighten with
screwdriver.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Turn handles into OFF position and replace AERATOR.
Apply a bead of PUTTY around underside
of DRAIN FLANGE (1) flange. Insert DRAIN
PLUG (2) into SINK drain hole.
Hold DRAIN PLUG (2) to prevent turning and
assemble GASKET (3), WASHER (4), and
LOCKNUT (5) from underneath sink.
Apply sealant to threaded end of TAILPIECE
and thread into lower end of DRAIN PLUG.
Connect other end to trap.
DRAIN ASSEMBLY (6542.140/.170)
PUTTY
SINK
SEALANT
3
INSTALL HANDLES
4
SERVICE
6
CARTRIDGE
SCREEN
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove HANDLE and BONNET NUT.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90° and replace.
Replace SPRING CLIP.
Replace BONNET NUT, HANDLE, SCREW,
and INDEX.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove HANDLE and BONNET NUT.
Remove CARTRIDGE by pulling up.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace BONNET NUT, HANDLE, SCREW
and INDEX.
SPRING
CLIP
STOP
WASHER
90°
10
3
5 5/16'' MIN.
MOUNTING SURFACE
11
11
1
2
3
1
2
2
Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5)
into mounting holes from underside of ledge.
Install LOCKNUTS (1), BRASS WASHERS (2) and RUBBER WASHERS (3) onto valve shanks.
Place RUBBER RING (11) into DECK ADAPTERS (10) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (5) position.
Slide FERRULE (13) and COUPLING NUT (14) to outlet of VALVE (5) and tighten
COUPLING NUT (14) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
VALVE ASSEMBLY
HOT
COLD
13
5
14
8
7
9
6
14
13
4
5
10
MOUNTING
LEDGE
11
10
Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is
properly seated on SHANK (7). Push COUPLING (9) into TEE (6) and
attach to SPOUT SHANK (7) and tighten.
1
3
4
5
6
4
2
1
2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
3
5
7
8
6
7