Sony MDR-AS100W - Manual

2
2
1
Stereo Headphones
3-289-105-11(1)
© 2008 Sony Corporation Printed in Thailand
MDR-AS100W
English
Features
• Sleek lightweight design and secure fitting headphones for active use.
• Wide 13.5 mm driver units achieve high quality sound with deep bass.
• Water-resistant design.
• 2-foot short cord ideal for armband use; supplied extension cord (2 feet)
ideal for general use.
Specifications
Type: Closed, dynamic / Driver unit: 13.5 mm, dome type (CCAW adopted) /
Power handling capacity: 100 mW (IEC*) / Impedance: 16
Ω at 1 kHz /
Sensitivity: 105 dB/mW / Frequency response: 8 - 25,000 Hz / Cord:
Approx. 0.61 m (24 in), OFC litz cord / Plug: Gold plated stereo mini plug /
Mass: Approx. 25 g (0.9 oz) without cord / Supplied accessories: Carrying
case (1), Extension cord (0.61 m, 24
in ) (1), Earbuds (S × 2,
M × 2, L × 2), Clip(1)
* IEC = International Electrotechnical Commmission
Design and specifications are subject to change without notice.
Wearing the headphones (see fig. A)
1 Adjust the length of the headband and the earpiece angle for a
comfortable fit.
2 Wear the headband on your head, and insert the earpiece marked R in
your right ear and the one marked L in your left ear.
If the angles of earpieces do not fit in with your ears
Adjust them by swiveling the housings. You can turn them to upwards
approx. 40 degrees or less.
How to install the earbuds correctly (see fig. B)
If the earbuds do not fit your ears correctly, low-bass sound may not be
heard. To enjoy better sound quality, change the earbuds to another size,
or adjust the earbuds position to sit on your ears comfortably and fit your
ears snugly. The M size earbuds are attached to the headphones before
shipment. If you feel the M size earbuds do not suit your ears, replace
them with the supplied S or L size earbuds. When you change the
earbuds, install them firmly on the headphones to prevent the earbuds
from detaching and remaining in your ear.
Cleaning the earbuds
Remove the earbuds from the headphones, and wash them with a mild
detergent solution.
How to re-attach the cord to the clip (see fig. C)
1 Hold the clip closed, and pull up the lever on the clip just a little.
2 Put the cord into the groove under the lever.
Notes
• If you pull up the lever on the clip without holding the clip closed, or
holding the clip closed but opening the lever too much, you cannot put
the cord into the groove under the lever.
• Do not catch the cord on the projection of the clip or do not wedge it into
the groove. It may damage the wires of the cord.
How to open the carrying case (see fig. D)
With your finger inserted into the recess, push and open the cover.
How to carry the headphones
1 Install the headband within the contour of the case, and insert the
earbuds into their ribs. (see fig. E-1, 2)
2 Wrap the cord around the center hub and insert the stereo mini plug in
the rib. (see fig. E-3)
3 Attach the lid of the case. (see fig. E-4)
Precautions
• Listening with headphones at high volume may affect your hearing. For
traffic safety, do not use while driving or cycling.
• Do not put weight or pressure on the headphones as it may cause the
headphones to deform during long storage.
• The earbuds may deteriorate due to long-term storage or use.
• Please keep your headphones clean at all times especially inside the
rubber earbud. (see fig. F)
If any dust or ear wax inside the earbud, you may experience some
listening difficulties.
• Install the earbuds firmly onto the headphones. If an earbud accidentally
detaches and is left in your ear, it may cause injury.
There is EP-EX1 available (sold separately) as an optional replacement
earbuds.
A
B
C
D
Extension cord
(supplied)
Stereo mini plug
4
3
F
,
Operating Instructions
Manual de instrucciones
E