American Standard 4" Centerset Lavatory and Bar Sink Faucets 5400 Series - Manual (Page 2)

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
A m e r i c a n S t a n d a r d I n c . 1 9 9 9 C
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time
SERVICE
1
5
3
CARTRIDGE
SCREEN
TAIL
PIECE
TEST INSTALLED FAUCET
4
Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Operate LIFT ROD and check DRAIN for leaks.
Turn handles into OFF position and replace AERATOR.
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90
° and replace.
Replace SPRING CLIP.
Replace ADAPTER, HANDLE, SCREW, and INSERT.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90
° .
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Unscrew CARTRIDGE with wrench.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace ADAPTER, HANDLE, SCREW,
and INSERT.
Apply a bead of PUTTY around underside
of DRAIN PLUG flange. Insert DRAIN
PLUG into SINK drain hole.
Hold DRAIN PLUG to prevent turning
and assemble GASKET, WASHER, and
LOCKNUT, from underneath sink.
Insert threaded end of TAILPIECE
into lower end of DRAIN PLUG.
Connect other end to trap.
DRAIN ASSEMBLY
(Models 5402 and 7402 only)
(Models 5401 and 7401 only)
PUTTY
FLANGE
DRAIN
PLUG
RUBBER
GASKET
WASHER
LOCKNUT
SINK
2
Apply a bead of PUTTY along the edge of the underside of the BODY and insert faucet
SHANKS through holes of SINK.
Turn off hot and cold water supplies before beginning.
CAUTION
Assemble RUBBER and BRASS WASHERS, and LOCKNUTS from underside of SINK.
Drop UPPER LIFT ROD through hole in BODY (models 5401 & 7401 only), align BODY
as far forward as possible and secure position by tightening LOCKNUTS. (Plastic LOCKNUTS
Connect the HOT water supply to the left SHANK and the COLD water supply to the right
SHANK using sealant, appropriate connectors, and COUPLING NUTS.
Refer to separate "Instruction Sheet" for assembly of handles.
UPPER LIFT ROD
SHANK
BODY
PUTTY
SINK
RUBBER WASHER
BRASS WASHER
LOCKNUT
COUPLING NUT
HOT
COLD
HANDLE SCREW
1/2" O.D. SLIP
on model 7490 are tightened by hand.)
3 4 0 6 3 M - B
INSTALL POP-UP DRAIN STOPPER
Push TAILPIECE down into TRAP (threaded end up).
Thread LOCKNUT, WASHER and GASKET onto
DRAIN BODY.
Apply a bead of PUTTY to underside of FLANGE.
Feed DRAIN BODY up through SINK and thread
FLANGE fully onto BODY.
Tighten LOCKNUT firmly, keeping the PIVOT ROD
pointed towards the back of the SINK.
Drop STOPPER into DRAIN BODY.
Pull TAILPIECE up and thread tightly
into DRAIN BODY.
Position EXTENSION ROD onto POP-UP ROD and
tighten THUMBSCREW.
Remove one end of CLIP from PIVOT ROD by
squeezing ends together while sliding.
Insert PIVOT ROD into second or third hole in
EXTENSION and reassemble CLIP. (EXTENSION
may need to be bent.)
Adjust STOPPER height by repositioning EXTENSION
and tightening THUMBSCREW.
FLANGE
SINK
GASKET
PIVOT
ROD
DRAIN
BODY
PUTTY
WASHER
LOCKNUT
TAILPIECE
TRAP
TAILPIECE CLIP
THUMBSCREW
POP-UP ROD
CLIP
PIVOT
ROD EXTENSION
ROD
TRAP
EXTENSION
ROD
SPRING
CLIP
STOP
WASHER
90 °