beautypg.com

American Standard 3120.019 User Manual

Yorkville™ elongated pressure-assisted toilet

background image

M43

© 2008 AS America Inc.

Revised 2/08

To Be Specified:

Color: ❏ White ❏ Bone ❏ Linen

❏ Silver ❏ Fawn Beige ❏ Black

Seat: American Standard #5324.019

Elongated “Rise and Shine” (with easy to clean
lift-off hinge system) solid plastic closed front
seat with cover.

Seat: American Standard #5325.024

Elongated “Rise and Shine” (with easy to clean
lift-off hinge system) solid plastic open front

seat with cover.

Alternate Seat:

Supply with Stop:

* Flushmate III tank system by Flushmate

®

Div. of Sloan Valve Co

YORKVILLE™ ELONGATED

PRESSURE-ASSISTED TOILET

VITREOUS CHINA

YORKVILLE™ ELONGATED
PRESSURE-ASSISTED TOILET

2320.101

• Vitreous china

• Low-consumption (6.0 Lpf/1.6 gpf)

Floor-mounted, back-outlet toilet

• Elongated bowl

• Pressure-assisted siphon jet flush action

• Side-mounted chrome trip lever

• Close-coupled flushometer tank*

• Speed Connect

®

tank/bowl coupling system

• 4 bolt caps

• Fully glazed 2" ballpass trapway

• 10" x 12" water surface area

• 100% factory flush tested

3120.019 Elongated bowl with four bolt

caps and two floor screws

4099.100 Flushometer tank complete with

coupling components

Component parts:

735084-400 Tank cover (specify color)

Nominal Dimensions:
813 x 495 x 749mm
(32" x 19-1/2" x 29-1/2")

Alternate Configurations:

4099.700 Tank and tank cover only

with tank cover locking device

4099.800 Tank and tank cover only

with right hand trip lever

Fixture only, seat and supply by others
Recommended working pressure range 20 psi - 80psi
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2 for Vitreous China Fixtures

NOTES:

WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-

FELT (WAX RING NOT RECOMMENDED).

SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED

SEPARATELY.

*

DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.

FOR ADDITIONAL INFORMATION REFER TO INSTALLATION

INSTRUCTIONS SUPPLIED.

IMPORTANT: Dimensions of fixtures are nominal and may vary within

the range of tolerances established by ANSI Standard A112.19.2. These

measurements are subject to change or cancellation. No responsibility is

assumed for use of superseded or voided pages.

749mm

(29-1/2)

235mm

(9-1/4)

356mm

(14)

381mm

(15)

470mm

(18-1/2)

648mm

(25-1/2)

813mm

(32)

C/L OF SEAT
POST HOLES
140 mm (5-1/2)
CENTER

FINISHED WALL

FINISHED
FLOOR

152

mm

(6)

6

4

m

m

(

2

-1

/2

)

324mm
(12-3/4)

C/L OF 1/2" DIA HOLES
152mm (6) CENTERS

76mm

(3)

76mm

(3)

*

222mm

(8-3/4)

102

mm

(4)

C/L OF
WASTE
OUTLET

13 x 19mm

(1/2 x 3/4)

SLOTS

FLEX
SUPPLY
AS REQ.

C/L

19mm

± 6mm

(3/4

± 1/4)

279mm

(11)

495mm

(19-1/2)

Replaces 2320.100