American Audio Pro-Scratch 2 - Manual (Page 18)

11. EDITING A LOOP:
Please note: Only the ending point of the loop may be edited. You may make your loop shorter or longer. Before
you can edit your seamless loop you obviously must first have created a seamless loop to edit. If you haven’t
created a SEAMLESS LOOP, follow the instructions in step 10 to create a loop. If a SEAMLESS LOOP has
already been created, press the RELOOP BUTTON (31) to activate your SEAMLESS LOOP (Figure 23) if it is
not already activated. To edit your seamless loop’s ending point:
1) Press the OUT BUTTON (32) to return to normal play from the loops cue point. (Figure 20). This will
disengage the SEAMLESS LOOP mode and allows you to edit the loops ending point.
2) Press the OUT BUTTON (32) again when you reach your new ending point (Figure 21).
- FOR A SHORTER LOOP: Press the OUT BUTTON (32) at sooner point in the track (Figure 21).
- FOR LONGER LOOP: Press the OUT BUTTON (32) at later point in the track (Figure 21).
BASIC OPERATIONS (CONT.)
3) Press the OUT BUTTON (32) to set the ending point for your SEAMLESS
LOOP (Figure 13). The IN BUTTON (14) and OUT BUTTON (32) LEDs will
immediately begin to flash rapidly, indicating the SEAMLESS LOOP mode
has been activated.
LCD LOOP INDICATORS - During a seamless loop, the LOOP (47) and
RELOOP (48) INDICATORS will turn on in the LCD DISPLAY (19) indication a
loop is active.
EXITING A LOOP - To exit a SEAMLESS LOOP, press the OUT
BUTTON (32). The IN BUTTON (14) and OUT BUTTON (32) LEDs
will remain on, but will stop flashing. Music playback will resume nor-
mal play (Figure 13). The IN BUTTON (14) and OUT BUTTON (32)
LEDs will remain on to remind you that a loop is stored in memory.
REPLAY LOOP - The RELOOP (31) function allows you to return to your
stored loop at any time. The IN BUTTON (14) and OUT BUTTON (32) LEDs
will indicate a loop is stored in memory, and may be played at any time. To
replay the loop, press the RELOOP BUTTON (31). The IN BUTTON (14) and
OUT BUTTON (32)
LEDs will again begin to flash indicating SEAMLESS LOOP
mode has been activated (Figure 14) and your stored loop will immediately
begin to play.
Figure 23
Figure 22
Figure 21
© American Audio ® - www.americandj.com - Pro-Scratch 2™ Instruction Manual Page 18
PARAMETER TIME
PARAMETER RATIO
EJECT
POWER
CUE 1 2 3 4 5 6 7 8 9 0
RELOOP
SINGLE
LOOP
REMAIN NONSTOP TOTAL ELAPSED
M T S
PROGRAM
LOCK KEY SYNC. BEAT
F PITCH BPM
CUE AUTO BPM
OFF
ON
FX MIX
BOP
ENTER
PAN FLANGER SKID PHASE
FX SELECT SGL/CTN
TIME REV.PLAY
TEMPO
LOCK 4%/8%/16%
TRANS ECHO SCRATCH FILTER HOLD
ON/OFF
SAMPLE PITCH
PARAMETER TIME
PARAMETER RATIO
EJECT
POWER
CUE 1 2 3 4 5 6 7 8 9 0
RELOOP
SINGLE
LOOP
REMAIN NONSTOP TOTAL ELAPSED
M T S
PROGRAM
LOCK KEY SYNC. BEAT
F PITCH BPM
CUE AUTO BPM
OFF
ON
FX MIX
BOP
ENTER
PAN FLANGER SKID PHASE
FX SELECT SGL/CTN
TIME REV.PLAY
TEMPO
LOCK 4%/8%/16%
TRANS ECHO SCRATCH FILTER HOLD
ON/OFF
SAMPLE PITCH
PARAMETER TIME
PARAMETER RATIO
EJECT
POWER
CUE
1 2 3 4 5 6 7 8 9 0
RELOOP
SINGLE
LOOP
REMAIN NONSTOP TOTAL ELAPSED
M T S
PROGRAM
LOCK KEY SYNC. BEAT
F PITCH BPM
CUE AUTO BPM
OFF
ON
FX MIX
BOP
ENTER
PAN FLANGER SKID PHASE
FX SELECT SGL/CTN
TIME REV.PLAY
TEMPO
LOCK 4%/8%/16%
TRANS ECHO SCRATCH FILTER HOLD
ON/OFF
SAMPLE PITCH