Allied Telesis AT-G8T GBIC - Manual

| | |
*613-000524 RevA*
613-000524 Rev. A
*613-000524 RevA*
613-000524 Rev. A
*613-000524 RevA*
613-000524 Rev. A
*613-000524 RevA*
613-000524 Rev. A
AT-G8T GBIC Transceiver Installation Guide
Overview
The AT-G8T GBIC transceiver is a self-contained Gigabit
Ethernet copper port that provides connectivity over twisted
pair cable for networking products that feature a standard
size GBIC expansion slot.
The GBIC features an RJ-45 connector and a maximum
operating distance of 100 meters (328 ft.). The transceiver
supports both shielded and unshielded twisted pair wiring.
Verifying Package Contents
Make sure that the AT-G8T GBIC transceiver and installation
instructions are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales
representative for assistance.
Cable Specifications
The GBIC transceiver uses shielded or unshielded Category
5 or 5E cable with a maximum operating distance of 100 m
(328 ft.). The AT-G8T GBIC transceiver uses a straight-
through cable regardless of the type of end node. A
crossover cable is not required.
Installing an AT-G8T GBIC Transceiver
To install an AT-G8T GBIC transceiver, perform the following
procedure:
Caution
The transceiver can be damaged by static electricity.
Be sure to observe all standard electrostatic discharge
(ESD) precautions, such as wearing an antistatic wrist
strap, to avoid damaging the device.
1. Remove the transceiver from the shipping package and
store the packaging material in a safe place.
2. Set the auto-negotiation switch to either ON or OFF to
enable or disable auto-negotiation on the transceiver.
3. Slide the transceiver into the GBIC slot.
If you are connecting the twisted pair cable to the GBIC
at this time, continue to step 4. Otherwise, stop here.
4. Remove the dust cover.
5. Connect the twisted pair cable to the transceiver.
AT-G8T GBIC Transceiver Installation Guide
Overview
The AT-G8T GBIC transceiver is a self-contained Gigabit
Ethernet copper port that provides connectivity over twisted
pair cable for networking products that feature a standard
size GBIC expansion slot.
The GBIC features an RJ-45 connector and a maximum
operating distance of 100 meters (328 ft.). The transceiver
supports both shielded and unshielded twisted pair wiring.
Verifying Package Contents
Make sure that the AT-G8T GBIC transceiver and installation
instructions are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales
representative for assistance.
Cable Specifications
The GBIC transceiver uses shielded or unshielded Category
5 or 5E cable with a maximum operating distance of 100 m
(328 ft.). The AT-G8T GBIC transceiver uses a straight-
through cable regardless of the type of end node. A
crossover cable is not required.
Installing an AT-G8T GBIC Transceiver
To install an AT-G8T GBIC transceiver, perform the following
procedure:
Caution
The transceiver can be damaged by static electricity.
Be sure to observe all standard electrostatic discharge
(ESD) precautions, such as wearing an antistatic wrist
strap, to avoid damaging the device.
1. Remove the transceiver from the shipping package and
store the packaging material in a safe place.
2. Set the auto-negotiation switch to either ON or OFF to
enable or disable auto-negotiation on the transceiver.
3. Slide the transceiver into the GBIC slot.
If you are connecting the twisted pair cable to the GBIC
at this time, continue to step 4. Otherwise, stop here.
4. Remove the dust cover.
5. Connect the twisted pair cable to the transceiver.
AT-G8T GBIC Transceiver Installation Guide
Overview
The AT-G8T GBIC transceiver is a self-contained Gigabit
Ethernet copper port that provides connectivity over twisted
pair cable for networking products that feature a standard
size GBIC expansion slot.
The GBIC features an RJ-45 connector and a maximum
operating distance of 100 meters (328 ft.). The transceiver
supports both shielded and unshielded twisted pair wiring.
Verifying Package Contents
Make sure that the AT-G8T GBIC transceiver and installation
instructions are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales
representative for assistance.
Cable Specifications
The GBIC transceiver uses shielded or unshielded Category
5 or 5E cable with a maximum operating distance of 100 m
(328 ft.). The AT-G8T GBIC transceiver uses a straight-
through cable regardless of the type of end node. A
crossover cable is not required.
Installing an AT-G8T GBIC Transceiver
To install an AT-G8T GBIC transceiver, perform the following
procedure:
Caution
The transceiver can be damaged by static electricity.
Be sure to observe all standard electrostatic discharge
(ESD) precautions, such as wearing an antistatic wrist
strap, to avoid damaging the device.
1. Remove the transceiver from the shipping package and
store the packaging material in a safe place.
2. Set the auto-negotiation switch to either ON or OFF to
enable or disable auto-negotiation on the transceiver.
3. Slide the transceiver into the GBIC slot.
If you are connecting the twisted pair cable to the GBIC
at this time, continue to step 4. Otherwise, stop here.
4. Remove the dust cover.
5. Connect the twisted pair cable to the transceiver.
AT-G8T GBIC Transceiver Installation Guide
Overview
The AT-G8T GBIC transceiver is a self-contained Gigabit
Ethernet copper port that provides connectivity over twisted
pair cable for networking products that feature a standard
size GBIC expansion slot.
The GBIC features an RJ-45 connector and a maximum
operating distance of 100 meters (328 ft.). The transceiver
supports both shielded and unshielded twisted pair wiring.
Verifying Package Contents
Make sure that the AT-G8T GBIC transceiver and installation
instructions are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales
representative for assistance.
Cable Specifications
The GBIC transceiver uses shielded or unshielded Category
5 or 5E cable with a maximum operating distance of 100 m
(328 ft.). The AT-G8T GBIC transceiver uses a straight-
through cable regardless of the type of end node. A
crossover cable is not required.
Installing an AT-G8T GBIC Transceiver
To install an AT-G8T GBIC transceiver, perform the following
procedure:
Caution
The transceiver can be damaged by static electricity.
Be sure to observe all standard electrostatic discharge
(ESD) precautions, such as wearing an antistatic wrist
strap, to avoid damaging the device.
1. Remove the transceiver from the shipping package and
store the packaging material in a safe place.
2. Set the auto-negotiation switch to either ON or OFF to
enable or disable auto-negotiation on the transceiver.
3. Slide the transceiver into the GBIC slot.
If you are connecting the twisted pair cable to the GBIC
at this time, continue to step 4. Otherwise, stop here.
4. Remove the dust cover.
5. Connect the twisted pair cable to the transceiver.