Serial ata hard disk drive connection, Right angle side, 28 chapter 2: hardware information – Asus EVOLUTION P5E64 WS User Manual
Page 54: P5e64 ws evolution sata connectors, P5b sata connectors, Sata2 sata1, Sata3 sata4, Sata6 sata5
2-28
Chapter 2: Hardware information
3. ICH9R Serial ATA connectors [blue] (7-pin SATA1-SATA6)
These connectors are for the Serial ATA signal cables for Serial ATA hard disk
drives and optical disk drives.
• When using the connectors in Standard IDE mode, connect the primary
(boot) hard disk drive to the SATA1/2 connector. Refer to the table below
for the recommended SATA hard disk drive connections.
• These connectors are set to Standard IDE mode by default. In Standard
IDE mode, you can connect Serial ATA boot/data hard drives to these
connectors. If you intend to create a Serial ATA RAID set using these
connectors, set the Configure SATA as item in the BIOS to [RAID]. See
section 4.3.6 SATA Configuration for details.
• Before creating a RAID set, refer to 5.4.3 Intel RAID configurations or the
manual bundled in the motherboard support DVD.
P5E64 WS EVOLUTION
®
P5E64 WS Evolution
SATA connectors
SATA2
SATA1
GN
D
RS
AT
A_TXP2
RS
AT
A_TXN2
GN
D
RS
AT
A_RXP2
RS
AT
A_RXN2
GN
D
GN
D
RS
AT
A_TXP1
RS
AT
A_TXN1
GN
D
RS
AT
A_RXP1
RS
AT
A_RXN1
GN
D
SATA3
SATA4
GN
D
RS
AT
A_TXP
3
RS
AT
A_TXN3
GN
D
RS
AT
A_RXP
3
RS
AT
A_RXN
3
GN
D
GN
D
RS
AT
A_TXP
4
RS
AT
A_TXN4
GN
D
RS
AT
A_RXP
4
RS
AT
A_RXN
4
GN
D
SATA6
SATA5
GN
D
RS
AT
A_TXP6
RS
AT
A_TXN6
GN
D
RS
AT
A_RXP6
RS
AT
A_RXN6
GN
D
GN
D
RS
AT
A_TXP5
RS
AT
A_TXN5
GN
D
RSA
TA
_RXP5
RS
AT
A_RXN5
GN
D
R
P5B
P5B SATA Connectors
G
ND
RS
AT
A_
TX
P1
RS
AT
A_
TX
N1
G
ND
RS
AT
A_
RX
P1
RS
AT
A_
RX
N1
G
ND
G
ND
RS
AT
A_
TX
P2
RS
AT
A_
TX
N2
G
ND
RS
AT
A_
RX
P2
RS
AT
A_
RX
N2
G
ND
G
ND
RS
AT
A_
TX
P3
RS
AT
A_
TX
N3
G
ND
RS
AT
A_
RX
P3
RS
AT
A_
RX
N3
G
ND
G
ND
RS
AT
A_
TX
P4
RS
AT
A_
TX
N4
G
ND
RS
AT
A_
RX
P4
RS
AT
A_
RX
N4
G
ND
SATA1
SATA4
SATA3
SATA2
Connect the right-angle side
of SATA signal cable to SATA
device. Or you may connect the
right-angle side of SATA cable to
the onboard SATA port to avoid
mechanical conflict with huge
graphics cards.
right angle side
Serial ATA hard disk drive connection
Connector
Color
Setting
Use
SATA 1/2
Red
Master
Boot disk
SATA 3/4
Red
Slave
Boot/Data disk
SATA 5/6
Red
Master
Boot disk