Siemens HB84K552 - Manual (Page 6)

Poista lastut, sähköisten rakenneosien
toiminta voi häiriytyä.
Laite työtason alla Ć kuva 1
Ympärille asennettavan kaapin
välipohjassa pitää olla tuuletusaukko Ć
ks. kuva 1.
Jos laite asennetaan keittotason alle, ota
keittotason asennusohje huomioon.
Laite korkeassa kaapissa Ć kuva 2
Laitteen saa asentaa vain saman
valmistajan, tuuletuksella varustetun
uunin yläpuolelle.
Asentaminen kylmälaitteen yläpuolelle on
mahdollista.
Laitetta ei saa asentaa höyryuunin,
yhdistelmähöyryuunin tai
astianpesukoneen yläpuolelle.
Asennus kulmaan Ć kuva 3
Jotta laitteen luukku saadaan avattua, ota
kulmaan asentaessasi huomioon mitat D.
Mitta E riippuu kalusteen etuosan
paksuudesta kahvan alapuolella.
Asennuksen valmistelu
Ć kuva 4 ja 5
J Asenna tarvittaessa välike Ć kuva 4.
J Säädä tarvittaessa laitteen luukun ja
laitteen kehyksen välistä rakoa Ć kuva 5.
Laitteen kiinnittäminen Ć
kuva 6
J Työnnä laite kunnolla paikalleen ja
kohdista keskelle.
J Älä taita liitäntäkaapelia.
J Ruuvaa laite kiinni.
J Työtason ja laitteen välistä rakoa ei saa
sulkea lisälistalla.
Irrotus
Kytke laitteesta virta pois. Irrota
kiinnitysruuvit. Nosta laitetta kevyesti ja
vedä se kokonaan ulos.
en
The following must be noted:
Only allow a licensed professional to
connect the appliance. The regulations of
the country and the local electricity
supplier apply.
During all installation work the appliance
must be disconnected from the power
supply.
The appliance corresponds to protection
class I and may only be operated with a
protective earth connection.
The socket must only be installed and the
power cable replaced by a qualified
electrician, and in accordance with the
appropriate regulations.
Identify the phase and neutral conductors
in the socket. Incorrect connection may
cause damage to the appliance.
The appliance must only be connected
with the power cable provided.
Connect the appliance only according to
the connection diagram. See the rating
plate for the voltage.
Connect the wires of the mains power
cable according to the colour coding:
Green
and yellow earth conductor $
Blue (zero) neutral conductor
Brown phase (external conductor)
Protection against accidental contact
must be ensured through the manner of
installation.
The appliance must be protected using a
16 A fuse.
When connecting the appliance, a safe
method for disconnecting the power
supply must be considered.
With a fixed connection, disconnection
must be performed via an allĆpole
isolating switch with a contact gap of at
least 3 mm.
Only in Sweden, Finland and
Norway
The appliance can also be connected
using the plug provided which has an
earthing contact system. This must be
accessible after installation. If this is not
the case, an allĆpole isolating switch must
be used on the installation side with a
contact gap of at least 3 mm.
Fitted units
The installation cabinet must not have a
back panel behind the appliance. A gap
of at least 45 mm must be maintained
between the wall and the base or back
panel of the unit above.
The installation cabinet must have a
ventilation opening of 50 cm 2 on the
front. For surround units with no
ventilation cutĆout in the back of the side
panels 200 cm 2 . To do this, cut back the
base panel or fit a ventilation grille.
Ventilation slots and intakes must not be
covered.
The safe operation of this appliance can
only be guaranteed if it has been installed
in accordance with these installation
instructions. The installer is liable for
losses incurred as a result of incorrect
installation.
Fitted units must be heatĆresistant up to
90 ºC, and adjacent unit fronts up to at
least 70 ºC.
Cut out the units and the work surface
before fitting the appliances. Remove
shavings as they can affect the function
of electrical components.
Oven under the work surface Ć
Figure 1
A ventilation cutĆout must be made in the
intermediate floor of the surround unit Ć
see Figure 1.
If the appliance is being installed beneath
a hob, observe the hob assembly
instructions.
Appliance in a tall unit Ć Figure 2
The appliance may only be fitted above a
ventilated oven from the same
manufacturer.
It is possible to fit the hob over a
refrigerator.
The appliance must not be fitted above
a steamer, combination steam oven or
a dishwasher.
Corner installation Ć Figure 3
To ensure that the appliance door can be
opened in the case of corner installation,
take account of dimension D.
Dimension E is dependent on the
thickness of the unit front under the
handle.
Preparing for installation Ć
Figure 4 and 5
J If necessary, fit the spacer Ć Figure 4.
J If necessary, adjust the gap between
the appliance door and the appliance
frame Ć Figure 5.
Securing the appliance Ć
Figure 6
J Fully insert the appliance and centre it.
J Do not kink the connecting cable.
J Screw the appliance into place.
J The gap between the worktop and the
appliance must not be closed using
additional battens.
Removal
Disconnect the appliance from the power
supply. Undo the securing screws. Raise
the appliance slightly and pull it out
completely.