beautypg.com

Important safety information, 2 important safety information, Safety – Wagner PaintREADY System User Manual

Page 2: Safety important safety information, Grounding instructions, Important electrical information, English 2

background image

Safety

Safety

Important Safety

Information

Read all safety information before

operating the equipment. Save these

instructions

Indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

a) To reduce the risks of fire or explosion, electrical shock and

the injury to persons, read and understand all instructions

included in this manual. Be familiar with the controls and

proper usage of the equipment.

Grounding Instructions

This product must be grounded. In the event of an electrical short circuit,

grounding reduces the risk of electric shock by providing an escape wire

for the electric current. This product is equipped with a cord having a

grounding wire with an appropriate grounding plug. The plug must

be plugged into an outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

waRnIng - Improper installation of the grounding plug

can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do

not connect the green grounding wire to either flat blade

terminal. The wire with insulation having a green outer surface with or

without yellow stripes is the grounding wire and must be connected to

the grounding pin.
Check with a qualified electrician or serviceman if the grounding

instructions are not completely understood, or if you are in doubt as

to whether the product is properly grounded. Do not modify the plug

provided. If the plug will not fit the outlet, have the proper outlet

installed by a qualified electrician.
This product is for use on a nominal 120 volt circuit and has a grounding

plug that looks like the plug illustrated below. Make sure that the

product is connected to an outlet having the same configuration as the

plug. No adapter should be used with this product.

Grounded Outlet

Grounding Pin

Cover for grounded outlet box

b) waRnIng - To reduce the risk of fire or

explosion:

1. Do not spray flammable or combustible

materials near an open flame, pilot lights

or sources of ignition such as hot objects, cigarettes, motors,

electrical equipment and electrical appliances. Avoid creating

sparks from connecting and disconnecting power cords.

2. For use with only water-based or mineral spirit-type materials

with a minimum flash point of 21ºC (70º F) — Do not spray

or clean with liquids having a flash point of less than 21ºC

(70º F). Flash point is the temperature at which a fluid can

produce enough vapor to ignite.

3. Verify that all containers and collection systems are grounded

to prevent static discharge.

4. Connect to a grounded outlet and use grounded extension

cords (electric models only). Do not use a 3 to 2 adapter.

5. Do not use a paint or solvent containing halogenated

hydrocarbons. Such as chlorine, bleach mildewcide,

methylene chloride and trichloroethane. They are not

compatible with aluminum. Contact the coating supplier

about compatibility of material with aluminum.

6. Keep spray area well ventilated. Keep a good supply of fresh

air moving through the area to keep the air within the spray

area free from accumulation of flammable vapors. Keep

pump assembly in well ventilated area. Do not spray pump

assembly.

7. Do not smoke in the spray area.
8. Do not operate light switches, engines, or similar spark

producing products in the spray area.

9. Keep area clean and free of paint or solvent containers, rags,

and other flammable materials.

10. Know the contents of the paint and solvents being sprayed.

Read all Material Safety Data Sheets (MSDS) and container

labels provided with the paints and solvents. Follow the paint

and solvent manufacture’s safety instructions.

11. Fire extinguisher equipment shall be present and working.

c) waRnIng - To reduce the risk of injury:
1. Always wear appropriate gloves, eye protection, clothing

and a respirator or mask when painting. Hazardous vapors

– Paints, solvents, insecticides, and other materials can be

harmful if inhaled or come in contact with body. Vapors can

cause severe nausea, fainting or poisoning.

2. Do not operate or spray near children. Keep children away

from equipment at all times.

3. Do not overreach or stand on an unstable support. Keep

effective footing and balance at all times.

4. Stay alert and watch what you are doing.
5. Do not operate the unit when fatigued or under the influence

of drugs or alcohol.

6. Never aim spray gun at any part of the body.
7. Follow all appropriate local, state, and national codes

governing ventilation, fire prevention, and operation.

8. The United States Government Safety Standards have

been adopted under the Occupational Safety and Health

Act (OSHA). These standards, particularly part 1910 of

the General Standards and part 1926 of the Construction

Standards should be consulted.

9. Use only manufacturer authorized parts. User assumes all

risks and liabilities when using parts that do not meet the

minimum specifications and safety devices of the turbine

manufacturer.

10. Power cord must be connected to a grounded circuit.
11. All hoses, swivels, guns and accessories must be rated at or

above 10 PSI.

12. Do not spray outdoors on windy days.
13. Hose may become hot and cause skin burn.
14. Use only Wagner HVLP hose.

d) waRnIng - To reduce the risk of electric shock:
1. Always remove turbine before cleaning.
2. Power cord must be connected to a grounded

circuit.

3. Never submerge electrical parts.
4. Never expose the equipment to rain. Store indoors.
5. Keep electrical cord plug and spray gun trigger free from

paint and other liquids. Never hold the cord at plug

connections to support the cord. Failure to observe may

result in an electrical shock.

Important Electrical Information

Use only a 3-wire extension cord that has a 3-blade grounding plug

and a 3-slot receptacle that will accept the plug on the product.

Make sure your extension cord is in good condition. When using

an extension cord, be sure to use one heavy enough to carry the

current your product will draw. An undersized cord will cause a

drop in line voltage resulting in loss of power and overheating. A

14 gauge or 12 gauge cord is recommended. If an extension cord is

to be used outdoors, it must be marked with the suffix W-A after the

cord type designation. For example, a designation of SJTW-A would

indicate that the cord would be appropriate for outdoor use.
Wagner Spray Tech accessory extension cords recommended:
P/N 0090241

20 foot extension cord

P/N 0090242

35 foot extension cord

IMPORTanT: Household use only.

English

2