Wagner Control Spray Max - Manual (Page 2)

English 2
Safety Safety
Important Safety
Information
Read all safety information before operating
the equipment. Save these instructions
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
a) To reduce the risks of fire or explosion, electrical shock and
the injury to persons, read and understand all instructions
included in this manual. Be familiar with the controls and
proper usage of the equipment.
Grounding Instructions
This product must be grounded. In the event of an electrical short
circuit, grounding reduces the risk of electric shock by providing an
escape wire for the electric current. This product is equipped with a
cord having a grounding wire with an appropriate grounding plug.
The plug must be plugged into an outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
warnIng - Improper installation of the grounding
plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary,
do not connect the green grounding wire to either flat
blade terminal. The wire with insulation having a green
outer surface with or without yellow stripes is the grounding wire and
must be connected to the grounding pin.
Check with a qualified electrician or serviceman if the grounding
instructions are not completely understood, or if you are in doubt
as to whether the product is properly grounded. Do not modify the
plug provided. If the plug will not fit the outlet, have the proper outlet
installed by a qualified electrician.
This product is for use on a nominal 120 volt circuit and has a
grounding plug that looks like the plug illustrated below. Make
sure that the product is connected to an outlet having the same
configuration as the plug. No adapter should be used with this
product.
Grounded Outlet
Grounding Pin
Cover for grounded outlet box
b) WARNING - To reduce the risk of fire
or explosion:
1. Do not spray flammable or combustible
materials near an open flame, pilot
lights or sources of ignition such as hot objects, cigarettes,
motors, electrical equipment and electrical appliances.
Avoid creating sparks from connecting and disconnecting
power cords.
2. For use with only water-based or mineral spirit-type
materials with a minimum flash point of 21ºC (70º F) — Do
not spray or clean with liquids having a flash point of less
than 21ºC (70º F). Flash point is the temperature at which a
fluid can produce enough vapor to ignite.
3. Verify that all containers and collection systems are
grounded to prevent static discharge.
4. Connect to a grounded outlet and use grounded extension
cords (electric models only). Do not use a 3 to 2 adapter.
5. Do not use a paint or solvent containing halogenated
hydrocarbons. Such as chlorine, bleach mildewcide,
methylene chloride and trichloroethane. They are not
compatible with aluminum. Contact the coating supplier
about compatibility of material with aluminum.
6. Keep spray area well ventilated. Keep a good supply of
fresh air moving through the area to keep the air within the
spray area free from accumulation of flammable vapors.
Keep pump assembly in well ventilated area. Do not spray
pump assembly.
7. Do not smoke in the spray area.
8. Do not operate light switches, engines, or similar spark
producing products in the spray area.
9. Keep area clean and free of paint or solvent containers,
rags, and other flammable materials.
10. Know the contents of the paint and solvents being sprayed.
Read all Material Safety Data Sheets (MSDS) and container
labels provided with the paints and solvents. Follow the
paint and solvent manufacture’s safety instructions.
11. Fire extinguisher equipment shall be present and working.
c) WARNING - To reduce the risk of injury:
1. Always wear appropriate gloves, eye protection, clothing
and a respirator or mask when painting. Hazardous vapors
– Paints, solvents, insecticides, and other materials can be
harmful if inhaled or come in contact with body. Vapors can
cause severe nausea, fainting or poisoning.
2. Do not operate or spray near children. Keep children away
from equipment at all times.
3. Do not overreach or stand on an unstable support. Keep
effective footing and balance at all times.
4. Stay alert and watch what you are doing.
5. Do not operate the unit when fatigued or under the influence
of drugs or alcohol.
6. Never aim spray gun at any part of the body.
7. Follow all appropriate local, state, and national codes
governing ventilation, fire prevention, and operation.
8. The United States Government Safety Standards have
been adopted under the Occupational Safety and Health
Act (OSHA). These standards, particularly part 1910 of
the General Standards and part 1926 of the Construction
Standards should be consulted.
9. Use only manufacturer authorized parts. User assumes all
risks and liabilities when using parts that do not meet the
minimum specifications and safety devices of the turbine
manufacturer.
10. Power cord must be connected to a grounded circuit.
11. All hoses, swivels, guns and accessories must be rated at
or above 10 PSI.
12. Do not spray outdoors on windy days.
13. Hose may become hot and cause skin burn.
14. Use only Wagner HVLP hose.
d) warnIng - To reduce the risk of electric
shock:
1. Always remove turbine before cleaning.
2. Power cord must be connected to a grounded circuit.
3. Never submerge electrical parts.
4. Never expose the equipment to rain. Store indoors.
5. Keep electrical cord plug and spray gun trigger free
from paint and other liquids. Never hold the cord at plug
connections to support the cord. Failure to observe may
result in an electrical shock.
Important Electrical Information
Use only a 3-wire extension cord that has a 3-blade grounding
plug and a 3-slot receptacle that will accept the plug on the
product. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting in
loss of power and overheating. A 14 gauge or 12 gauge cord
is recommended. If an extension cord is to be used outdoors,
it must be marked with the suffix W-A after the cord type
designation. For example, a designation of SJTW-A would
indicate that the cord would be appropriate for outdoor use.
Wagner Spray Tech accessory extension cords recommended:
P/N 0090241 20 foot extension cord
P/N 0090242 35 foot extension cord
IMPORTANT: Household use only.