beautypg.com

Using the cd/mp3-cd/wma-cd/usb device – Kenwood M-505USB-S User Manual

Page 11

background image

EN

11

Using the CD/MP3-CD/WMA-CD/USB device

Preparation

Loading a disc

1

Press CD/USB (CD/USB) button to select CD

mode.

2

Press

(

0) button to open the CD tray.

3

Place a disc into the tray with the label facing

up.

4

Press

(

0) button to close the CD tray.

For a CD, the total playtime and total number of
tracks will appear in the display.
For an MP3-CD and WMA-CD, the total album
number and total fi le number will appear on the
display.

• To remove the disc, press (

0) button, grasp the disc by its

edges, and carefully pull it out.

Inserting a USB device

1

Press

the button to select standby mode.

2

Insert a USB device to the USB connector on the

front panel.

3

Press CD/USB (CD/USB) button to select USB

mode.

• To ensure good system performance; wait until the unit

completely reads the disc/USB device before proceeding.

• If the disc compartment is not loaded with a disc, “NO DISC” is

displayed. If the disc is unreadable, “ERR DISC” is displayed.

• If the disc is unreadable or there is no playable audio fi le in

the USB device, “NO DATA” is displayed.

• For audio fi les, reading time may exceed 10 seconds due

to the large number of songs compiled into one disc/USB
device.

• For audio fi les, “A” on the display represents ALBUM.
• For audio fi les, the total album number on the display

indicates the number of all the albums recorded in the disc/
USB device.

• The icon “MP3” appears only when an MP3-fi le is played.
The icon “WMA” appears only when an WMA-fi le is played.
• Insert or remove the USB device while in the standby mode.

Sound may be interrupted when inserting or removing the
USB device. This may occur even when the sound is not
played or recorded from/to the USB device.
When playing or recording from/to the USB device, removing
it or turning the power off may corrupt the sound source and
get it unplayable.

Playing a disc/USB device

Press FWD PLAY

6 (6) button to start playback.

The track/fi le number and elapsed playing time of
the current track/fi le appear on the display.

• To interrupt playback, press FWD PLAY

6 (6) button.

The playing time starts fl ashing.
To resume playback, press FWD PLAY

6 (6) button

again.

• To stop playback, press STOP

7 (7 stop) button.

Selecting a desired track/passage

To select a desired track

Press SEARCH/TUNING

4 or ¢ (4 or ¢

search +/–) button repeatedly until the desired
track appears on the display.

• If playback is stopped, press FWD PLAY

6 (6) button to

start playback.

• The digit buttons, 0–9 on the remote control unit can also be

used to select a track.

Press the digit buttons as shown below:
To select track 2 : 2 and ENTER
To select track 23 : 2, 3 and ENTER
To select track 120 (Audio fi le only) : 1, 2 and 0

To search for a particular passage during
playback

Press and hold SEARCH/TUNING

4 or ¢ (4 or

¢ search +/–) button for more than 3 seconds.
Press the FWD PLAY

6 (6) button when the

desired passage is located.

M-505USB_EN_r12.indd 11

M-505USB_EN_r12.indd 11

07.8.29 4:44:43 PM

07.8.29 4:44:43 PM

This manual is related to the following products: