Bluetooth setup, Bluetooth setting, Bluetooth setup 53 – Kenwood KDC-BT92SD User Manual
Page 27: Bluetooth
53
|
KDC-BT92SD
English
|
54
Bluetooth Setup
Bluetooth Setting
You can select following Bluetooth Setting items.
1
Enter Bluetooth mode
Press the [
] button.
✍
You can also select from “Settings” in Menu List
mode.
2
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings”.
3
Select the Menu item
Turn the [VOL] knob and press it when the
desired item is displayed.
Display
Overview
“SMS Inbox”
Display the received short message.
Refer to
“BT Settings”
“Pairing”
“Device Regist.” Register a Bluetooth device (pairing).
Refer to
“Phone
Selection”
Select a cell-phone or Bluetooth audio player
connection
Refer to
.
“Audio Selection”
“SPCL DVC
Select”
Register a Bluetooth device (pairing).
Refer to
“Device Delete” Cancel registration of the Bluetooth device.
Refer to
“SMS”
“SMS
Download”
Download a short message.
Refer to
.
“SMS Reply”
Select a method to reply to the received SMS.
Refer to
.
“SMS Message” Create an original message.
Refer to
“Detailed Setup”
Move to detailed item.
“PIN Code Edit” Specify the PIN code required when registering
this unit using the Bluetooth device.
Refer to
.
“Auto Answer” Answer a call automatically after lapse of the
preset time interval for automatic answer.
“OFF”/ “0s” – “8s” – “99s”
“Auto
Reconnect”
Automatically reconnects the selected
Bluetooth device when radio wave becomes
strong enough, even after it is disconnected.
“ON”/ “OFF”
✍
When this function is turned ON, the Bluetooth device
is reconnected if it has been disconnected by selecting
“Phone Selection”/ “Audio Selection”.
“Bluetooth HF/
Audio”
You can specify output speakers for hands-free
voice communication and Bluetooth audio
sound.
“Front”: Outputs audio from the front speakers.
“All”: Outputs audio from the front and rear
speakers.
“Call Beep”
You can output a beep from the speaker when
a call comes in.
“ON”: Beep is heard.
“OFF”: Beep is canceled.
“BT F/W Update” Display the version of the firmware of this unit.
“Mic Gain”
Adjust the sensitivity of the microphone for a
telephone call. Adjust the voice of caller. Setting
to “+” increases the voice volume.
“1” – “20” – “30”
“NR Level”
Reduce the noises generated by surrounding
environment without changing the microphone
volume. Adjust the voice of caller when it is
not clear. Setting to “+” increases the noise
reduction.
“–1” – “0” – “+1”
“Echo Cancel
Level“
Adjust the level of echo cancellation. Setting to
“+” increases the echo cancel reduction.
“–1” – “0” – “+1”
( : Factory setting)
4
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
5
Exit BT Settings mode
Press the [
] button.
4
MENU VOL
¢
Remarks
• “Auto Answer” (Setting the Time Interval for Automatic
Answer)
This function automatically answers (responds to) a call
after lapse of the preset time interval for automatic answer.
“OFF” : Does not answer the phone call automatically.
“0” : Automatically answers the phone call at once.
“1s” – “99s” : Automatically answers the phone call after
lapse of 1 – 99 seconds.
⁄
• If the time set in the cell-phone is shorter than that set in
the unit, the former will be used.
• This function does not work for call waiting.
• “BT F/W Update” (Displaying the Firmware Version)
Display the version of the firmware of this unit.
For how to update the firmware, access our web site.
http://www.kenwood.com/cs/ce/bt/