Dwyer TS3 - Manual (Page 3)

Parameter Description
Compressor / Set Point Menu
SEt Sets the Ambient Temperature set point between r1 and r2
r0 Differential or hysteresis for set point
(For d0 = re)
Ambient temperature ≥ SEt + r0
Output On
Ambient temperature ≤ SEt Output Off
(For d0 = in)
Ambient temperature ≤ SEt - r0
Output On
Ambient temperature ≥ SEt Output Off
r1 Minimum value for set point
r2 Maximum value for set point
c0 Minimum time compressor must remain off before being
restarted
c1 Duration of cold cycle
c2 During probe error, time that output is engaged
c3 During probe error, time that output is disengaged
c4 Minimum time compressor must stay on
c5 Minimum time between compressors starts
Defrost Menu
d0 Selection for Heating or Cooling Operation
re = Cooling
in = Heating
d2 Maximum time the control will be in defrost cycle. If set to zero,
control will not defrost.
d3 Hour of the day for the first defrost. No defrost cycles will take
place before this time.
d4 Upon powering on the control, delay time before first defrost
cycle.
d5 Display during defrost cycle.
Off = Current temperature displayed.
On = Temperature at start of defrost cycle displayed until
defrost cycle ends and the temperature is less than or equal
to starting temperature or after the time is set in d6.
d6 Maximum time before the display returns to normal reading
after a defrost cycle.
d7 Time after defrost cycle before the compressor can be started.
d8 Time between defrost cycles. If set to 0, defrost must be
manually actuated.
d11 Minimum duration the control remains in defrost cycle.
d14 Units to count the defrost cycle
rt = according to the time the controller was on.
ct = according to the time the compressor was on.
HdE Hours until next defrost cycle.
ndE Minutes until next defrost cycle.
Display Menu
P0 Selection of Engineering Unit (F or C)
P1 Ambient Probe Calibration Adjustment
P4 Decimal Point Present
Alarm Menu
A0 Alarm Differential or hysteresis
A1 High Alarm Set Point (Deviation Value)
On when temperature reaches Set + A1 and off at Set +
A1 - A0
A2 Low Alarm Set Point (Deviation Value)
A3 Time of Alarm Inhibit after Continuous Cool Cycle
A4 Time of Alarm Inhibit after Defrost Cycle
A6 Time of Alarm Inhibit after Power Up
A7 Time since Alarm Initiated until Validated
Initial Setup Menu
Hor Real Time Hours
nin Real Time Minutes
H0 Restore Factory Configuration
H2 Keypad Password Protected
Yes = code is necessary to start/stop defrost or continuous
cold cycle. One minute after entering the code, keypad is
locked again
No = Keypad not protected
H3 Compressor delay time upon power up
H4 Address for serial communications (Need Model TS485
communication module)
H5 Input code to Parameters (factory set at 0)
H6 Input Probe Types: PTC or NTC
H11 HACCP Alarm recording enabled or disabled
dAt Real Time Date can be programmed by holding the set key for
3 seconds. Then, use arrows to select day. Press set to store
day; use arrows to access month and year
td The display refreshes at 1 degree if actual temperature is
greater than 1 degree higher td seconds before during defrost
and open door conditions
Front Panel Operation
Set Point Setup
• Press the Set key once and Set will be displayed.
• Press Set key again and set point value will be shown.
• Uses the Up and Down arrows to adjust set point.
• Press the Set key to save the new set point.
• Press Set and Down arrow at same time to exit.
Time Setup
• Press the Set Key once and Set will be displayed.
• Use the Up and Down arrow until Hor is displayed for adjusting the
hours.
• Press the Set key to view the current value.
• Use the Up and Down arrow to adjust to current time.
• Press the Set key for 8 seconds to save the new time (Pro will flash
on display once the value is saved).
• Press the Set key to return to the previous menu.
• Use the Up and Down arrow until Nin is displayed for adjusting the
minutes.
• Repeat steps 3 through 6.
• Press the Set and Down arrow at the same time to exit.
Parameter Programming
The parameters are organized into 6 programming menus (COn, dEF,
PrO, ALA, HAC, and Ini) (HAC is only accessible when H11 = yes).
• Press the Set key for 8 seconds until 0 is displayed.
• Use the Up and Down arrows to reach the assigned security code
(factory setting for this code is 0).
• Press the Set key to accept the code.
• Use the Up and Down Arrows to select programming menu to
enter.
• Press the Set key to reach the parameters under each
programming menu.
• Use the Up and Down Arrows to scroll through the parameters.
• Press the Set key to view the value of the parameters.
• Use the Up and Down Arrows to change the values of the
parameters.
• Press the Set key to save the changes.
• Press the Set and Down Arrow to go back to the programming
menu selection.
• Press the Set and Down Arrow a second time to exit.