MAGURA HS33 (2014) - Manual (Page 22)

22
m
aintenanCe
THE PASSION PEOPLE
www.magura.com
. ) Push.the.hose.cover. ( 4 ) .upwards. [ L3 ] .
. ) Unscrew.the.screw.plug. ( 5 ) .from.the.filler.hole.in.the.brake.cylinder.
. ) Screw.the.barbed.fitting.of.the.filling.syringe. ( 2 ) .into.the.filler.hole.and.
tighten.to.a.torque.of. max. 4 N·m (35 lbf·in). [ L3 ] .
. ) Unscrew.the.lower.clamping.screw.of.the.clamping.clip.on.the.brake.
lever.
. ) HS 11: Turn.the.brake.lever.so.it.is.pointing.vertically.upwards. [ L4 ] .
. ) HS 33: Turn.the.brake.lever.so.it.is.pointing.horizontally.forwards.or.
backwards.
[ L5 ] .
О О
HS 33: The.bleed.hole.is.located.above.the.hose.inlet.
. ) Tighten.the.clamping.screw.slightly.
. ) HS 11: Push.the.hose.cover. ( 6 ) .away.from.the.brake.lever. [ L4 ] .
. ) HS 11: Unscrew.the.barbed.fitting. ( 7 ) .of.the.brake.hose.from.the.brake.
lever.until.3 turns.of.the.thread.can.be.seen.
. ) HS 11: Unscrew.the.EBT.plug. ( 8 ) .from.the.bleed.hole. ( 9 ) .
. ) HS 33: Unscrew.the.EBT.screw. ( 10 ) .from.the.bleed.hole. ( 11 ) . [ L5 ] .
. ) Insert.the.bleed.syringe. ( 3 ) .tightly.into.the.bleed.hole. [ L6 ] /. [ L7 ] .
. ) Press.MAGURA.Royal Blood slowly.out.of.the.filling.syringe. ( 2 ) .through.
the.brake.system.–.tap.lightly.on.the.brake.cylinder.and.brake.lever.
during.this.process.
. ) Flick.the.brake.lever.2–3.times.
О О
This.loosens.air.bubbles.and.they.rise.into.the.bleed.syringe. ( 3 )
. [ L6 ] /. [ L7 ] .
. ) Continue.the.process.until.you.cannot.see.any.more.air.bubbles.
О О
The.brake.system.has.been.bled.
Oil loss when removing the bleed syringe.
Î – Have.a.clean.cloth.at.hand.
Î – Block.the.top.hole.with.your.thumb.before.removing.the.syringe.
Î – After.removal.quickly.place.a.finger.on.the.tip.of.the.syringe.
. ) Pull.the.bleed.syringe.out.of.the.bleed.hole.
. ) HS 11: Push.the.EBT.plug. ( 8 ) .firmly.into.the.bleed.hole. ( 9 ) . [ L4 ] .
. ) HS 11: Screw.the.barbed.fitting. ( 7 ) .of.the.brake.hose.into.the.brake.lever.
and.tighten.to.a.torque.of. max. 4 N·m (35 lbf·in).
. ) HS 33: Screw.the.EBT.screw. ( 10 ) .into.the.bleed.hole. ( 11 ) .and.tighten.to.a.
tightening.torque.of. max. 0.5 N·m (4 lbf·in). [ L5 ] .
О О
HS 33: The.EBT.screw.fits.flush.with.the.housing.
. ) Unscrew.the.barbed.fitting.of.the.filling.syringe. ( 2 ) .from.the.filler.
hole. [ L3 ] .
. ) Screw.the.screw.plug. ( 4 ) .into.the.filler.hole. ( 5 ) .and.tighten.to.a.tighten-
ing.torque.of. 4 N·m (35 lbf·in). [ L3 ] .
. ) Thoroughly.clean.up.any.oil.residues.on.any.surfaces.–.particularly.on.
brake.track.areas.and.brake.pads.
. ) Pull.and.hold.brake.lever.
. ) Make.sure.that.all.connections.are.tight.
. ) HS 11: Push.the.hose.cover. ( 6 ) .onto.the.brake.lever.
. ) Move.the.brake.lever.into.the.customary.position.and.secure.– see.
i
nstalling Brake lever
,.page.16.
. ) Set.the.pressure.point.– see. s etting the pressure pOint / COmpensating fOr paD
wear
,.page.19.