Installing brake cylinders, Adjusting brake cylinders, Installing.brake.cylinders – MAGURA HS33 (2014) User Manual
Page 17: Adjusting.brake.cylinders
17
E
N
g
LI
S
H
Installing brake cylinders
Important.– see.
.
)
Screw.the.quick.release.screw.
.into.the.right.cantilever.socket.(as.
seen.from.above).–.by.10–12.turns.at.first.
[
B1
]
.
.
)
Push.the.mounting.plate.onto.the.cantilever.socket..
[
B1
]
О
О
The.spacers.
.are.only.required.if.the.mounting.plate.or.adapter.are.in.
contact.with.the.fork.–.max..1.shim.per.cantilever.socket,.flattened.
side.uppermost!
О
О
The.lettering."EVO2".must.be.legible.from.the.front.(as.seen.from.above).
.
)
Place.the.left.brake.cylinder.(2.connecting.lines).on.the.left.cantilever.
socket.(as.seen.from.above).and.mounting.plate.–.secure.with.a.washer.
and.socket.screw.
.
)
Screw.in.the.adapter.screw.
.until.the.brake.
cylinder.and.adapter.can.just.still.be.moved.
.
)
Place.the.right.brake.cylinder.with.open.quick.release.skewer.
.(OPEN).
onto.the.right.cantilever.socket/quick.release.screw.and.mounting.
plate.–.set.the.quick.release.lever.to.the.up.position.(CLOSED).
.
)
Screw.in.the.adapter.screw.
.until.the.
brake.cylinder.and.adapter.can.just.still.be.moved.
Adjusting brake cylinders
.
)
Install.the.wheel.into.the.dropouts.as.far.as.it.will.go.–.preferably.with-
out.tires.
.
)
Make.sure.that.the.rim.is.located.exactly.in.the.middle.between.the.
fork.blades.or.seat.stays.of.the.rear.triangle.–.centre.the.wheel.if.
.necessary.
Restricted adjustment capability.
The.exclusive.purpose.of.the.pressure.point.adjusting.screw.(TPA).is.to.
compensate.for.brake.pad.wear..Do.not.use.the.TPA.for.the.basic.setting.
of.the.brake.cylinders.–.the.brake.shoes.must.be.fully.advanced..Other-
wise.there.might.not.be.sufficient.adjustment.travel.available.later.on.
.
)
Make.sure.that.the.pressure.point.adjusting.screws.(TPA).
.are.un-
screwed.to.the.stop.(-).
.
О
О
Brake.shoes.are.fully.advanced.
.
)
Push.the.brake.cylinders.inwards.until.the.brake.pads.are.in.full,.flat.
contact.with.the.brake.track.area..
.
)
Move.the.adapter.up.or.down.if.necessary.until.the.top.edges.of.the.
brake.pads.are.1–2.mm.below.the.edge.of.the.rim.
О
О
Brake.pads.are.in.full,.flat.contact.with.the.brake.track.area.
О
О
Brake.pads.are.aligned.exactly.parallel.with.the.rim.
О
О
Brake.pads.cannot.come.into.contact.with.the.tires.
О
О
Adapters.are.at.the.same.height.
.
)
Pull.the.brake.lever.
carefully.
О
О
Brake.shoes.retract.
О
О
Brake.cylinders.are.pushed.outwards.
.
)
Carefully.pull.the.brake.lever.and.release.until.a.gap.of.1–1.5.mm.is.
produced.on.one.side.between.the.brake.pad.and.brake.track.area..
.
)
Then,.on.this.side:.tighten.the.adapter.screw.
.to.
a.tightening.torque.of.
max. 6 N·m (53 lbf·in).
.or.set.the.quick.
release.skewer.to.the.definitive.pressure.– see.
.
)
Carefully.pull.the.brake.lever.and.release.until.a.gap.of.1–1.5.mm.is.
also.produced.on.the.other.side.between.the.brake.pad.and.brake.track.
area..
.
)
Then,.on.this.side:.tighten.the.adapter.screw.
.to.
a.tightening.torque.of.
max. 6 N·m (53 lbf·in).
.or.set.the.quick.
release.skewer.to.the.definitive.pressure.– see.