Adjusting the quick release skewer, Installing the brake booster, Shortening brake hose – MAGURA HS33 (2014) User Manual
Page 18: Adjusting the brake levers, Adjusting.the.quick.release, Skewer, Installing.the.brake.booster, Shortening.brake.hose, Adjusting.the.brake.levers, E.– see
18
THE PASSION PEOPLE
www.magura.com
Adjusting the quick release skewer
.
)
Operate.the.quick.release.lever.–.open/close.
L
L
If.the.quick.release.lever.can.be.closed.too.easily,.the.quick.release.
screw.
(
1
)
.must.be.adjusted.
.
)
Move.the.quick.release.lever.up.(CLOSED).
.
)
Screw.in.the.quick.release.screw.by.¼.turn.clockwise.
.
)
Operate.the.quick.release.lever.–.open/close.
.
)
Repeat.the.procedure.if.necessary.
Installing the brake booster
.
)
Unscrew.the.right.adapter.screw.
.(as.seen.from.above).
.
)
Push.the.brake.booster.onto.the.left.adapter.screw.
.
)
Secure.the.brake.booster.with.the.adapter.screw.
.and.washer.
.
)
Tighten.the.right.adapter.screw..
.with.a.tightening.torque.of.
max. 6 Nm (53 lbf·in).
Shortening brake hose
Important.– see.
.
)
Push.the.double.hose.cover.
.upwards.
.
)
Cut.off.the.brake.hose.approx..12.mm.before.the.end.of.the.hose.–.use.
a.MAGURA.hose.cutter.if.required.
.
)
Twist.the.barbed.fitting.
.out.of.the.brake.cylinder.with.the.remains.of.
the.hose.
О
О
The.cut-off.barbed.fitting.cannot.be.reused!
.
)
Hold.the.end.of.the.brake.hose.to.the.brake.cylinder
Unusable brake hose – because it is too short.
Î
–
Calculate.the.insertion.depth.(~5.mm).of.the.brake.hose.in.the.brake.
cylinder
.
.
)
Mark.the.cut.on.the.brake.hose.
.
)
Place.the.brake.hose.on.a.solid.surface.(wood,.plastic,.etc.).and.cut.at.
right.angles.with.a.sharp.blade.–.if.required.use.the.MAGURA.hose.
cutter.
.
)
Place.the.sleeve.nut.
.and.olive.
.on.the.brake.hose
.
)
Insert.the.brake.hose.into.the.brake.cylinder.to.the.stop.and.hold.in.
position.
.
)
Screw.the.sleeve.nut.
.into.the.brake.cylinder.and.tighten.to.a.tighten-
ing.torque.of.
4 N·m (35 lbf·in)
[
B1
]
.
.
)
Remove.any.oil.residues.thoroughly.
.
)
Pull.and.hold.brake.lever.
.
)
Make.sure.that.all.connections.are.tight.
.
)
Push.the.hose.cover.
.downwards.
Adjusting the brake levers
L
L
You.can.adjust.the.position.(grip.width).of.the.brake.levers.of.your.
MAGURA.HS.according.to.your.requirements.
This.adjustment.does.not.have.any.effect.on.the.pressure.point.of.the.
brake!
.
)
Screw.the.adjusting.screw.
.out.
(
-
)
.
О
О
Brake.lever.moves.closer.to.the.handlebar.
.
)
Screw.the.adjusting.screw.in.
(
+
)
.
О
О
Brake.lever.moves.further.away.from.the.handlebar.
О
О
All.installation.work.is.complete.–.the.brake.is.ready.for.use.
o
n
the
mo
ve