Catskill Craftsmen 51524 - Manual (Page 4)

1 1/2” Long 3/16” DIA. Steel Pin
4 used in
this step
5/8” Phillips Flat Head #8 Screw
3 used in this step
Magnet Plate
7/8” Truss Head Bolt
4 used
in this step
1/2” Phillips Flat Head #4 Screw
1 used in this step
STEP 1
Door Prep
A. Insert/Tap ONE 1 1/2” pin into
each end of both doors. DON’T
OVERDRIVE PINS! Pins should
stick up about 1/2” when seated. OK
if loose.
B. Attach the door spacer to the
left door with 5/8” #8 screws. The
spacer has a space at the top to al-
low magnet clearance and is almost
flush with the bottom of the door.
C. Attach the magnet plate (may be
stuck to the magnet) with the small
FLAT HEAD screw to the top of the
right door. Small bumps on plate go
next to wood.
D. Attach the door
handles with 7/8”
Truss Head Machine
Screw.
RIGHT DOOR
LEFT DOOR
STEP 2
Tap Pins Into Brace Ends
Take the 2 front braces and tap/insert one 3/4”
steel pin into each end of both braces until seated.
About 3/8” will stick out when seated. Ok if loose.
4 used in this step
3/4” Long 3/16” DIA. Steel Pin
STEP 3
Assemble Spice Rack
Insert retainer
rods into holes
Fasten Shelves with
1 1/4” Phillips Flat Head
#8 Screw (Bronze)
Pilot holes in shelves
go toward back
1 3/4” Phillips Flat Head Bolt (8)
HARDWARE 51524
Magnet Pack
7/8” Truss Head Machine Screw (6)
3/4” Long 3/16” DIA. Steel Pin (4)
1” Long 3/16” DIA. Steel Pin (8)
1 1/2” Long 3/16 DIA. Steel Pin (4)
Cam (2)
10-24 Hex Nut (8)
Nickel Handle (3)
Caster Socket (4)
Locking Wheel Caster (2) Non-Locking Wheel Caster (2) Towel Bar (1)
5/8” #6 Pan Head Screw (2)
1/2” Phillips Flat Head #4 Screw (1)
Magnet (1) Magnet Plate (1)
14” Drawer Glide (1 Set )
Drawer
Cabinet
L-Bracket (4)
Cam Posts (2)
1 1/4” Phillips Flat Head #8 Screw (23)
5/8” Phillips Head #8 Screw (3)
Spice Rack Retainer Rods (2)
3/16” Flat Washer (6)
Towel Bar Post (2)
1” Phillips Flat Head #8 Screw (4)
5/8 Wooden Disk (8)
Note: Use the 8 Bronze screws
to assemble the spice rack
(Used on Spice Rack
& Side Handle/Towel Bar)
(Used to attach
the door spacer)
(Used to attach
the drawer front)
5/8” Phillips Flat Head #7 Screw (8)
(used on “L” Bracket)
5/8” Phillips Flat Head #7 Screw (4)
(used on cabinet glide)
5/8” Phillips Flat Head #5 Screw (4)
(used to attach drawer glide)
8 Bronze used
in this step
1 1/4” Phillips Flat Head #8 Screw
1 1/2” Long 3/16” DIA. Steel Pin
4 used in
this step
5/8” Phillips Flat Head #8 Screw
3 used in this step
Magnet Plate
7/8” Truss Head Bolt
4 used
in this step
1/2” Phillips Flat Head #4 Screw
1 used in this step