Wellsaw 1316S - Manual (Page 25)

23
Blade Guides
for 1" Blade
1 152158-003 Blade Guide Ass'y, D.E. between 6090 and 6272
(includes items 5 - 31& 35 - 37, minus 7,12,& 28)
152158-005 Blade Guide Assy, D.E. before 6090 and after 6272
2 152159-003 Blade Guide Ass'y, I. E. between 6090 and 6272
(includes items 5 thru 31& 35 - 37 minus 6,11& 29)
152159-001 Blade Guide Assy, I.E. before 6090 and after 6272
3 152160-003 Guide Support Ass'y, D.E. between 6090 and 6272
(includes items 13 thru 27 plus 29, 36 & 37)
152160-001 Guide Support Assy, D.E. before 6090 and after 6272
4 152161-003 Guide Support Ass'y, I.E. between 6090 and 6272
(includes items 13 thru 28 plus 36 & 37)
152161-001 Guide Support Assy, I.E. before 6090 and after 6272
5 105335-001 Hand Wheel & Screw
6 152118 Roller Guide Bracket, D.E.
7 152117 Roller Guide Bracket, I.E.
8 100004-018 Cap Screw, HH 5/16-18 x 1
9 100029-002 Flat Washer, 1/4
10 152155 Vertical Adjusting Block
11 152121-002 Horizontal Adjusting Block, D.E.
12 152121-003 Horizontal Adjusting Block, I.E.
13 152151 Adjusting Bolt
14 100053-036 Roll Pin, 1/4 x 2 (later S/N's)
15 152153 Carbide Back up Guide Block
16 100023-006 Nylon Lock Nut, 1/4-20
17 152156 Adjusting Knob
18 100136-009 Spring
19 152157 Stud
20 106317 Fixed Carbide Guide
21 100008-004 Cap Screw, HH 5/16-18 x 5/8
22 150465 Eccentric Roller Axle between 6090 and 6272
B-109 Eccentric Roller Axle before 6090 and after 6272
23 100416-001 Bearing s/n before 6090 and after 6272 uses 4 of these and no others
24 100097-001 Roller Guide Washer
25 100027-005 Lock Washer, Shakeproof
26 101300 Hex Nut, 5/16-18
27 B-043 Roller Axle
28 152119 Guide Support, I.E.
29 152120 Guide Support, D.E.
30 100324-009 Hose Barb, 1/4" hose, 90 deg
31 100218-018 Tubing Clamp, 3/8
32 100350-018 Coolant Hose, D.E. 1/4" x 18"
32a 100350-040 Cooant Hose, I.E. 1/4" x 40"
100350-068 Coolant Hose, I.E. for 1316S-EXTEND 1/4" x 68"
35 100013-005 Machine Screw, BH 10-32 x 3/8
36 100417-001 Bearing only used between 6090 and 6272
37 100406-001 Bearing only used between 6090 and 6272
38 100035-013 Set screw
for serial #s between 6090 and 6272. Serial numbers before
and after, use single bearings 100416-001 (SEE NEXT PAGE)