Yokogawa JUXTA VJCE - Manual (Page 7)

7
All Rights Reserved. Copyright © 1999, Yokogawa M&C Corporation IM 77J0C51-01E 2nd Edition July 23,2004-00
5. ASSIGNMENT OF INPUT/OUTPUT TERMINALS AND POWER SUPPLY TERMINALS
5.1 Assignment of Input/Output Terminals
Mountable Signal Conditioners
Input Terminal
1 3 4 6 2 5
Output-2 Terminal
VJH1, VJH7, VJHF, VJHR
VJQ0, VJQ7
VJXS, VJX7
VJC1 (*1)
VJT6
VJU7 (TC or mV input)
VJR6
VJU7 (RTD input)
VJS2, VJS7
VJA1
VJA5
VJA7
VJA4 (*1)
VJB1
VJG1
VJB3
VJD1
VJP1
VJP4
VJP8
VJQ2 (*2)
VJQ8
VJSS
VJF1
ϩ Ϫ
Channel-1 Channel-2
ϩ Ϫ ϩ Ϫ
ϩ Ϫ
A B B
PS ϩ Ϫ N.C.
N.C. ϩ Ϫ
A Ϯ
V Ϯ
V Ϯ
N.C. ϩ Ϫ
PS ϩ ϩ Ϫ
PS ϩ ϩ Ϫ
A/V Ϯ
Channel-1 Channel-2
ϩ – ϩ Ϫ
ϩ Ϫ ϩ Ϫ
N.C. N.C. N.C. N.C.
100% CENTER 0%
ϩ Ϫ
ϩ Ϫ
ϩ Ϫ
ϩ Ϫ
ϩ Ϫ
ϩ Ϫ
ϩ Ϫ
ϩ Ϫ
ϩ Ϫ
N.C. N.C.
N.C. N.C.
Input through one-touch fitting л 6 of the VJF1.
N.C. N.C.
N.C. N.C.
N.C. N.C.
N.C. N.C.
N.C. N.C.
N.C. N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
Channel-2
ϩ Ϫ
Channel-2
ϩ Ϫ
ϩ Ϫ
When using internal power
supply
When using external power
supply (When used as an
isolator)
Non-voltage contact / Voltage contact
Internally powered current pulse
(two-wire system)
Internally powered voltage pulse
(three-wire system)
*1: For 2-channel type of VJC1 and VJA4, only the voltage output can be mounted on VJCE. Output of channel-1 is output to the connector (CN1).
*2: Since VJQ2 is single output type, output-2 terminals are N.C.
*3: When receiving current input (current pulse), external shunt resistor (receiving resistor) is required.
(*3)
(*3) (*3)
(*3)
“N.C.” in the table denotes unassigned terminals.
RJC
L
N
40 39
38 37
36 35
34 33
32 31
30 29
28 27
26 25
24 23
22 21
20 19
18 17
16 15
14 13
12 11
10 09
08 07
06 05
04 03
02 01
40 1 +
39 –
38 2 +
37 –
36 3 +
35 –
34 4 +
33 –
32 5 +
31 –
30 6 +
29 –
28 7 +
27 –
26 8 +
25 –
24 9 +
23 –
22 10 +
21 –
20 11 +
19 –
18 12 +
17 –
16 13 +
15 –
14 14 +
13 –
12 15 +
11 –
10 16 +
09 –
08
07
06
05
04
03
02
01
Pin No. Slot No. CN1
CN1
Connector's Pin Assignment
Note: The figure represents the
connector when viewed from
the connector cable.
Input Terminals Output-2 Teminals
SLOT*
1
2 * 5
4
3 6
“*” in the figure above denotes a slot number.
Slots are numbered from 1 to 16, beginning
with the leftmost slot, when viewed from the
VJCE front.
● VJCE-011
CN1 connector's pin assignmet is same as VJCE-011.
VJH1, VJH7, VJHF, VJHR, VJQ0
VJQ7, VJXS, VJX7, VJHK
Mountable Signal Conditioners
Output-2 Terminal Output-1 Terminal
ϩ Ϫ ϩ Ϫ
7 9 2 5
Output Terminals
SLOT*
2 5
7 9 “*” in the figure on the left denotes a slot num-
ber. Slots are numbered from 1 to 16, beginning
with the leftmost slot, when viewed from the
VJCE front.
● VJCE-012