Reelcraft Display Stand - Manual (Page 2)

Step 5:
Gather the two remaining cross bars (#3)
and four preassembled corner brackets
(#10). Slide a corner bracket (#10) into
each end of the cross bar (#3) locating the
nuts of the brackets into one of the slots
of the cross bar (#3). Position the corner
brackets (#10) so that the outside edge of
each bracket is flush with each end of the
cross bar (#3). Tighten the four screws to
secure the two brackets to the cross bar.
(See figures 7 and 8). Repeat process for
the second cross bar (#3).
Step 6:
Position the two upright (#2) & front leg
(#4) assemblies flat on a hard surface
with the legs pointing up. Slide one of the
preassembled cross bars (#3), with the
brackets pointing toward the legs, into the
slots located inside the two uprights (#2).
Position the cross bar (#3) twelve inches
from the top of the uprights (#2) to the top
of the cross bar (#3). Be sure to measure
each side of the cross bar. Tighten the four
screws in the brackets to secure the cross
bar (#3) into position (see figure 9).
Step 7:
Place one display stand adapter plate (#1)
on the secured cross bar (#3) by sliding
the bend end of the plate around the cross
bar. From the leg end of the uprights slide
one of the preassembled cross bars with
access holes (#8), with the corner brackets
(#10) pointing away from the legs and
the access holes facing up, into the slots
located inside the two uprights (#2). Posi-
tion the cross bar (#8) so that the bottom
of the cross bar (#8) is flush with the bot-
tom of the display stand adapter plate (#1).
Tighten the four screws in the brackets
to secure the cross bar with access holes
(#8) into position (see figure 10).
Step 8:
From the leg end of the uprights, slide the
remaining preassembled cross bar (#3),
with the corner brackets (#10) pointing to-
ward the legs, into the slots located inside
the two uprights (#2). Position the cross
bar (#3) six inches from the bottom of the
secured cross bar with access holes (#8)
to the top of the cross bar (#3), be sure to
measure each side of the cross bar (#3).
Tighten the four screws in the brackets to
secure the cross bar (#3) into position.
Step 9:
Place one display stand adapter plate (#1)
on the second secured cross bar (#3) by
sliding the bent end of the plate around
the cross bar (#3). From the leg end of the
uprights (#2) slide the remaining preas-
sembled cross bar with access holes (#8),
with the corner brackets (#10) pointing
away from the front legs (#4), into the
slots located inside the two uprights (#2).
Position the cross bar (#8) so that the bot-
tom of the cross bar (#8) is flush with the
bottom of the display stand adapter plate
(#1). Tighten the four screws in the brack-
ets to secure the cross bar with access
holes (#8) into position (see figure 11).
Step 10:
Gather the four 45° support brackets (#7),
sixteen cap screws (#12) and sixteen
flange nyloc nuts (#9). Preassemble the
support brackets (#7) as shown in figure
12. The two support brackets (#7) on the
left will be for the left side of the display
stand and the two on the right will be for
the right side of the display stand.
Step 11:
Slide the top left side preassembled sup-
port brackets (#7) into the bottom end of
the left upright until it is near the middle of
the lower set of cross bars. The cap screw
(#12) heads will slide into the slots so the
the flange nyloc nuts (#9) will be exposed
(see figure 15).
Reelcraft Display Stand
Page 2 www.reelcraft.com
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13