TREND 3xtend_EINC L_230 - Manual (Page 4)

4 3xtend/EINC L/230 Installation Instructions TG200812 Issue 3 3/9/08
3xtend/EINC L/230 Installation Instructions
1 2 3 4
R S 2 3 2 R x T x
O K
O K L O N
1 2
2 8 - 3 6 V 2 4 V E T H E R N E T T R E N D L A N T - T + R - R + L I N K D A T A L O N O K L O N T E R M A D D R E S S - B A U D S R V P I N
1 2 3 4 5 6 7 8 9 1 0
L A N
M A C A d d r 0 0 . 1 0 . 7 0 . 0 0 . U D . B B
O / S
S / N o : Q 3 B _ _ _ _ X 7 3 0 1 0 0 0 3 I P A d d r L o c a t i o n
M A C A d d r 0 0 . 1 0 . 7 0 . 0 0 . U D . B B S / N o : Q 3 B _ _ _ _ X 7 3 0 1 0 0 0 3 X T N D - 4 0 0 0 0 7 0 9 6
I P A d d r
3 X t r e a m
1 2 3 4 R S 2 3 2 R x T x O K
O K L O N
1 2
2 8 - 3 6 V 2 4 V E T H E R N E T T R E N D L A N T - T + R - R + L I N K D A T A
L O N O K L O N T E R M A D D R E S S - B A U D S R V P I N
1 2 3 4 5 6 7 8 9 1 0
L A N
M A C A d d r 0 0 . 1 0 . 7 0 . 0 0 . U D . B B
O / S
S / N o : Q 3 B _ _ _ _ X 7 3 0 1 0 0 0 3 I P A d d r L o c a t i o n
M A C A d d r 0 0 . 1 0 . 7 0 . 0 0 . U D . B B S / N o : Q 3 B _ _ _ _ X 7 3 0 1 0 0 0 3 X T N D - 4 0 0 0 0 7 0 9 6
I P A d d r
3 X t r e a m
1.3 INSTALLATION - FIXING (Continued)
T R T R T R T R
T R T R T R T R
2 wire
Connect Current Loop
8
X
T
T R
R
4 5 6 7
T- T+ R- R+
X
T
T R
R
T
T R
R
4 5 6 7
T- T+ R- R+
4 wire
Additional terminals
Note only 1 INC type node on a single Lan.
If the 3xtend/EINC L’s current loop is not to be connected (i.e
3xtend/EINC L is only to interface between Ethernet and
L
ON W ORKS network) a loop back should be fitted. as shown
1 2 3 4
T- T+ R- R+
IMPORTANT
Maximum Cable distance
Terminal size 0.14 to 2.5
mm
2 (25 to 14 AWG).
Terminal size 0.14 to 2.5
mm
2 (25 to 14 AWG).
9
Connect L ON W ORKS ® Bus
Polarity independent
Terminal size 0.14 to 2.5 mm
2
(25 to 14 AWG).
LON
1 2
Normal current loop Lan cable is not recommended.
Do not use screened cable.
Maximum Cable distance
Cable 9k6 baud 19k2 baud 38k4 baud * No. of Wires
Belden 9182 1000 m (1090 yds) 700 m (765 yds) 500 m (545 yds) 2
Belden 9207 1000 m (1090 yds) 500 m (545 yds) 350 m (380 yds) 2
IQ System TP/1/1/22/HF/200 (Belden 8761) 700 m (765 yds) 350 m (380 yds) 250 m (270 yds) 2
IQSystem TP/2/2/22/HF/200 (Belden 8723) 500 m (545 yds) 250 m (270 yds) 125 m (135 yds) 4
Recommended
Cables
Max bus length
Max node to
node
Belden 85102 500 m (545 yds) 500 m (545 yds)
Trend
TP/1/0/16/HF/200
(Belden 8471)
500 m (545 yds) 400 m (430 yds)
UL Level IV, 22 AWG 500 m (545 yds) 400 m (430 yds)
JY(St) Y2 x 2 x 0.8 500 m (545 yds) 320 m (350 yds)
TIA568A Cat. 5, 24
AWG
450 m (490 yds) 250 m (270 yds)
Note that the 3xtend/EINC L is not compatible with LONC.
The LONC must be bound on a L
ON W ORKS network, and the
3xtend/EINC L cannot be bound.