TREND NBOX_EINC - Manual (Page 7)

2 - 3 NBOX/EINC Installation Instructions TG200152 Issue 2/D 4/7/06
Installation Instructions - Sheet 2 NBOX/EINC
15
Configure Addressing Details with IPTool (Continued)
1. Change if address clash on Ethernet or if routers between EINCs.
2. May change UDP port if port already used on Ethernet, or if multiple internetworks (i.e. sites) required on subnet (see Data Sheet).
3. Enables EINC virtual CNC to access Ethernet PC across router, or EINC to find other IQ system Ethernet devices across
router.
4. Also used by IQ system Supervisors and software tools to access EINC (Device address always 126).
5. Virtual CNCs inoperative until address set up.
6. Set up each virtual CNC used, separately.
7. Same port number to be set up in supervisor to communicate with virtual CNC.
8. Use virtual CNC in alarm mode to send alarms to Ethernet 962 v3 or greater/963 which connects via TCP dial up.
9. Lowest IP address (IQ3xcite or EINC) on each subnet across router to be set up; as many as possible in each subnet recommended.
10. If using 'updatelist' facility (not recommeded for mixed EINC/IQ3xcite system) also set up this EINC's details (and other
EINC's on this EINC's subnet, if not broadcast).
11. Out of the factory mode is ‘unconfigured’ which changes to ‘networked’ on first write to EINC by IPTool.
1.4 INSTALLATION - CONFIGURATION (Continued)
Parameter Setting Default Function Condition Note
Virtual CNCx
(x = 1 to 4)
CNC
Address node address 1, 4 to 9, 11 to
119
4
Node address of virtual CNC on virtual
Trend Lan
If virtual CNC is to be used 5,6
Port address Ethernet port 1 to 32767 disabled Ethernet port of virtual CNC
If virtual CNC is to be used
and if default needs to be
changed
6,7
alarm IP
address IP address
e.g. 171.193.6.106
disabled
IP address of target device (e.g.
supervisor)
if CNC used in alarm mode 6,8
Remote Trend
Device x
(remote EINCs)
(x = 1 to 20) IP Address
IP address
0.0.0.0 to 255.255.255.255
empty list
IP address of IQ system Ethernet device
other side of router
If network to span router
9,
10
Subnet Mask
Mask
0.0.0.0 to 255.255.255.255
empty list
Subnet mask of IQ system Ethernet
device other side of router
Device Mode networked unconfigured networked/stand alone on Ethernet
Set to stand alone if only IQ
system device on Ethernet
11
16
a Enter configuration mode using SET. The top level
prompt will be displayed as below.
b Configure the optional settings the relevant upper
case letter and pressing ENTER. If a value has been
changed X+ENTER will confirm it and return to the
top menu, whereas Q+ENTER will quit and return
with the value unchanged. The table below describes
the settings.
SET Manual TE200147
Configure Optional Settings Using SET
Note that it may be necessary to set up a virtual CNC in the
EINC if one is not available elsewhere on the network.
EINC L Data Sheet TA200137
1 If set to zero - no alarms reported.
2 Language type values:0=English, 1=Spanish, 2=Finnish, 3=Swedish, 4=Norwegian, 5=Danish, 6=German, 7=Italian, 8=Portuguese, 9=French.
3 Broadcast preferable as it enables the internetwork link to be made via the subnet of EINCs across router, rather than one EINC. However,
normally stopped by router.
4 This facility allows remoteEincs list in one EINC to be set up, and then the list (including Broadcast status) to be copied to all other EINCs
so that internetwork across routers can be formed (not recommended for mixed EINC/IQ3 system).
Parameter Setting Function Condition Note
addRess
iDentifier
15 alphanumeric
characters - not
/\({;?* characters Identifier for Lan Always set for supervisors/Display Panels
local
network
alarms to Address
node address 1, 4-9,
11-119 node address of EINC alarm target for
Trend current loop network alarms
If current loop network alarms to be reported 1
Remote
lan Lan number
1, 4-9, 11-119 Lan number of EINC alarm target for
Trend current loop network alarms
If current loop network alarms to be reported 1
ethernet
alarms to
addrEss
node address 1, 4-9,
11-119 node address of EINC alarm target for
Ethernet alarms
If Ethernet alarms to be reported 1
remoTe
lan Lan number
1, 4-9, 11-119 Lan number of EINC alarm target for
Ethernet alarms
If Ethernet alarms to be reported 1
alarm language tyPe 0 to 9 (digit) Selects language of network alarms If language to be changed 2
User
Pin number Protects changes in configuration mode
Default is blank (unprotected). Set up if security
required.
generator number random number for default PIN generation
Read only, give to Technical Support with Ethernet
mac address for default PIN see steps (17 and 19).
remoteEincs send as Broadcast Y (1) or N (0)
Broadcast to EINC subnet if Y or directed
to 1 EINC on subnet if N
Default Y, broadcast. Change if broadcast messages
prohibited by router
3
uPdatelist
Copy your remote EINC
list to other EINCs (Y/N) Copies remoteEincs list to local subnet and all subnets with
EINC in list
If internetwork to span router, and to faciliate setup 4