Magnum Venus Plastech PATRIOT SS PAT-CCP-LS-0590-SS - Manual (Page 16)

MAGNUM VENUS PLASTECH Patriot SS Chop Check Manual 16
DISASSEMBLY PROCEDURE:
Note: As you disassemble, lay the parts out on a towel or rag in the order you take
them apart. This will help you remember how they go back together. Inspect each
part for wear or damage and note parts that require replacement.
1.
If not already done, move the pump to the bottom of the down stroke.
2. Unscrew the four Hex Nuts (F-HN-06C) from the end of the Tie Rods (PAT-CCP-0520).
3. Pull the Inlet Bell Flange (PAT-CCP-0537) off the Tie Rods (PAT-CCP-0520).
4. Remove Hex Bolt (F-HB-04F-08) from the bottom of the Priming Rod (PAT-CCP-
0527-SS). If the Priming Rod (PAT-CCP-0527-SS) spins put a wrench on the
wrench flats of the Priming Rod just above the Priming Piston (PAT-CCP-0523).
5. Remove the Backup Washers (PAT-CCP-0528), Relief Washer (PAT-CCP-0525) and
the Priming Piston (PAT-CCP-0523) from the Priming Rod (PAT-CCP-0527-SS).
6. Unscrew the Tie Rods (PAT-CCP-0520) out of the Outlet Body (PAT-CCP-0501-SS).
7. Pull the Cylinder (PAT-CCP-0519-SS) out of the Outlet Body (PAT-CCP-0501-SS)
and off the Piston (PAT-CCP-0507-SS). This will also force the Intake Valve (PAT-
CCP-0531-SS) off the end of the Priming Rod (PAT-CCP-0527-SS).
8. Remove Lower Seat (PAT-CCP-0518-SS) from out of the end of the Cylinder (PAT-
CCP-0519-SS).
9. Remove the loose Intake Valve (PAT-CCP-0531-SS), Spacer (PAT-CCP-0529-SS)
and Valve Stop (PAT-CCP-0530) out of the end of the Cylinder (PAT-CCP-0519-SS).
10. Remove the Piston Bushing (PAT-CCP-0513) and Piston Seal Assembly (PAT-CCP-
0514) out of the other end of the Cylinder (PAT-CCP-0519-SS).
11. Unscrew the Valve Nut (PAT-CCP-0532) from the Intake Valve (PAT-CCP-0531-SS)
12. Remove both of the Foot Valve Seals (PAT-CCP-0536) from inside the Intake Valve
(PAT-CCP-0531-SS).
13. Remove the Intake Bushing (PAT-CCP-0533) from inside the Valve Nut (PAT-CCP-
0532).
14. Pull the Fluid Rod (PAT-CCP-0508-SS) and Piston assembly (PAT-CCP-0507-SS)
out of the Outlet Body (PAT-CCP-0501-SS) and Rod Seal assemblies (PAT-CCP-
0516)
– set a side for now.
15. Remove the Packing Nut (PAT-CCP-0504) from the top of the Outlet Body (PAT-
CCP-0501-SS).
16. Remove the Rod Bushing (PAT-CCP-0505) and Rod Seal assemblies (PAT-CCP-
0516) from the top of the Outlet Body (PAT-CCP-0501-SS).