Impulse V2406-24I Series - Manual (Page 2)

2 w w w. m o x a . c o m i n f o @ m o x a . c o m
Railway Computers
Hardware Specifications
Computer
CPU: Intel Atom N270 1.6 GHz processor
OS (pre-installed): Linux or Windows Embedded Standard 2009
System Chipset: Intel 945GSE + ICH7-M
BIOS: 8 Mbit Flash BIOS, PLCC type, ACPI function supported
FSB: 533 MHz
System Memory: 1 x 200-pin DDR2 SODIMM socket supporting DDR2
533 up to 2 GB; 1 GB built in
USB: USB 2.0 compliant hosts, type A connectors x 2; supports
system boot up, M12 connector x 1
Storage
Built-in: 2 GB onboard industrial DOM to store OS
Storage Expansion: CompactFlash socket for CF card expansion,
supporting CF Type-I/II
HDD Support: 1 SATA-II connector for HDD expansion
Other Peripherals
KB/MS: 1 PS/2 interface supporting standard PS/2 keyboard and
mouse through Y-type cable
Audio: Line-in, line-out interface
Display
Graphics Controller: Intel Gen 3.5 Integrated Graphics Engine, 250
MHz core render clock and 200 MHz core display clock at 1.05-V core
voltage
VGA Interface: DB15 female connector, up to 2048 x 1536 resolution
DVI Interface: DVI-I connector (chrontel CH7307 SDVO to DVI
transmitter), up to 1600 x 1200 resolution
Ethernet Interface
LAN: 2 auto-sensing 10/100 Mbps ports (M12)
Serial Interface
Serial Standards: 4 RS-232/422/485 ports*, software selectable (DB9
male)
*COM1’s pin 9 signal can be set by jumper as N/C (default), +5 V, or +12 V
ESD Protection: 8 KV for all signals
Serial Communication Parameters
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: RTS/CTS, XON/XOFF, ADDC® (automatic data direction
control) for RS-485
Baudrate: 50 bps to 921.6 Kbps (non-standard baudrates supported;
see user’s manual for details)
Serial Signals
RS-232: TxD, RxD, DTR, DSR, RTS, CTS, DCD, GND
RS-422: TxD+, TxD-, RxD+, RxD-, GND
RS-485-4w: TxD+, TxD-, RxD+, RxD-, GND
RS-485-2w: Data+, Data-, GND
Digital Input
Input Channels: 6, source type
Input Voltage: 0 to 30 VDC at 25 Hz
Digital Input Levels for Dry Contacts:
• Logic level 0: Close to GND
• Logic level 1: Open
Digital Input Levels for Wet Contacts:
• Logic level 0: +3 V max.
• Logic level 1: +10 V to +30 V (Source to DI)
Isolation: 3 KV optical isolation
Digital Output
Output Channels: 2, sink type
Output Current: Max. 200 mA per channel
On-state Voltage: 24 VDC nominal, open collector to 30 VDC
Connector Type: 10-pin screw terminal block (6 DI points, 2 DO
points, DI Source, GND)
Isolation: 3 KV optical isolation
LEDs
System: Power, Storage
LAN: 10M/Link x 2, 100M/Link x 2
Serial: TX x 4, RX x 4
Switches and Buttons
Power Switch: On/Off (front panel)
Reset Button: For warm reboot (front panel)
Physical Characteristics
Housing: Aluminum
Weight: 4 kg
Dimensions:
Without ears: 250 x 98 x 154 mm (9.84 x 3.86 x 6.06 in)
With ears: 275 x 104 x 154 mm (10.83 x 4.09 x 6.06 in)
Mounting: DIN rail, wall, VESA
Environmental Limits
Operating Temperature:
Standard models: -25 to 60°C (-13 to 140°F)
Wide temp. models: -40 to 70°C (-40 to 158°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)
Anti-vibration: EN 50155 standard
Anti-shock: EN 50155 standard
Conformal Coating: Available with *-CT models
Power Requirements
Input Voltage: 12 to 48 VDC (M12 connector)
Note: Compliant with EN 50155 on 24 VDC
Power Consumption: 26 W
2.16 A @ 12 VDC
1.08 A @ 24 VDC
542 mA @ 48 VDC
Rear View
Serial Port x 4
(RS-232/422/485, DB9)
DI x 6
DO x 2
USB 2.0 Host x 2
(Type A)
Reset Button
Serial LEDs
(Tx, Rx)
Antenna Hole x 4
(Reserved)
Antenna Hole x 2
(Reserved)