beautypg.com

Using the paddle, Add switchlinc to a scene as an insteon controller, Owner’s manual and tech support – INSTEON SwitchLinc Dimmer 100-277VAC (dual band) (2478D) Quick Start User Manual

Page 2: Fcc/ul and etl/ul statements

background image

INSTEON Limited Warranty – INSTEON warrants to original consumer of this product for a period of 2 years from

date of purchase, this product will be free from defects in material and workmanship and will perform in substantial

conformity with its Owner's Manual. Warranty shall not apply to defects caused by misuse or neglect.

Protected under U.S. and foreign patents (see www.insteon.com) © Copyright 2012

INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845, www. Insteon.com

Using the Paddle

Paddle

Tap

Double-Tap

Press and Hold

Top

Ramp to on-level

Fast on

Brighten

Bottom

Ramp to off

Fast off

Dim

Adding SwitchLinc to a Scene as an INSTEON Responder

1) Press and hold scene controller button until it beeps

1

Controller LED will start blinking

2) Tap SwitchLinc on

Load will turn on

3) Press and hold SwitchLinc Set button until it double-beeps

Controller’s LED will stop blinking and will double-beep

2

4) Confirm scene addition was successful by tapping controller scene button on and off

The light connected to SwitchLinc will respond appropriately

Add SwitchLinc to a Scene as an INSTEON Controller

1)

Press and hold SwitchLinc’s Set button until it beeps

SwitchLinc LED will blink

2)

Adjust the scene responder(s) to the “state” you want when scene is activated from SwitchLinc (e.g., 50%, 25% or

even off)

3

3)

Press and hold responder Set button until it double-beeps (or until its LED/load flashes)

SwitchLinc will double-beep

and its LED will stop blinking

4

Responder LED will stop blinking and it may double-beep

4

4)

Confirm scene addition was successful by tapping SwitchLinc paddle on and off

Responder will toggle between the scene’s on-level and off

Owner’s Manual and Tech Support

Owner’s Manual and current Quick Start Guide:

http://www.insteon.com/support

Call: INSTEON Support Line at 800-762-7845

FCC/UL and ETL/UL Statements

This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas

produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

CAUTION - To reduce the risk of overheating and possible damage to other equipment do not install to control a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a transformer-

supplied appliance.

Gradateurs commandant une lampe a filament de tungstene – afin de reduire le risqué de surchauffe et la possibilite d’endommagement a d’autres materiels, ne pas installer pour commader une prise,

un appareil a moteur, une lampe fluorescente ou un appareil alimente par un transformateur.

1

If the controller does not have a beeper, wait until its LED begins blinking

2

Most models

3

If the responder is a multi-scene device such as a KeypadLinc, tap the scene button you wish to control until its LED is in the desired scene state (on or off)

4

If either the SwitchLinc or responder’s LED continues to blink, the addition failed. Tap the device’s Set button until LED stops blinking and try again.